why does my Volvo XC90 Second Generation (2015-2024) make a clicking noise when turning

Volvo XC90 Second Generation (2015-2024)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

580 words

Problem Statement

Learn how to diagnose and fix clicking noise when turning in Volvo XC90. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical systems.
•Allow the vehicle to cool before working on brakes or suspension components.

Symptoms

•Clicking or popping noise when turning the steering wheel
•Noise occurs more prominently during sharp turns
•Vibration felt through the steering wheel
•Potential loss of power steering assistance
•Uneven tire wear observed on front tires

Diagnostic Steps

1
Inspect the front CV joints for signs of damage or wear.
2
Check the condition of the wheel bearings for play or roughness.
3
Examine the suspension components, including control arms and bushings, for wear or damage.
4
Test the power steering fluid level and inspect for leaks.
5
Perform a visual inspection of the tires for uneven wear patterns.
6
Lift the vehicle and spin the wheels to listen for abnormal noises.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Jack and jack stands
•Screwdrivers
•Bearing puller
•Multimeter

Parts Required

•CV joint assembly (if applicable)
•Wheel bearings (if applicable)
•Control arm bushings (if applicable)
•Brake pads (if calipers were removed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front CV joints for signs of damage or wear.
2
Check the condition of the wheel bearings for play or roughness.
3
Examine the suspension components, including control arms and bushings, for wear or damage.
4
Test the power steering fluid level and inspect for leaks.
5
Perform a visual inspection of the tires for uneven wear patterns.
6
Lift the vehicle and spin the wheels to listen for abnormal noises.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is on a level surface and secure it with wheel chocks.
Disconnect the battery for safety.

2. Inspect and Replace CV Joints

Remove the Wheel:
- Loosen lug nuts and lift the vehicle using a jack.
- Support the vehicle with jack stands and remove the wheel.
Check CV Joint Boots:
- Inspect the outer and inner CV joint boots for tears or leaks.
- If damaged, proceed to replace the affected CV joint.
Remove CV Joint:
- Remove the axle nut using a socket wrench (torque specifications: typically 80-100 ft-lbs).
- Detach the CV joint from the hub by using a puller tool if necessary.
Install New CV Joint:
- Apply grease to the new CV joint and slide it into place.
- Reinstall the axle nut and torque it to specifications.

3. Inspect and Replace Wheel Bearings

Remove Brake Caliper and Rotor:
- Unbolt and secure the brake caliper away from the rotor.
- Remove the rotor from the hub.
Check Wheel Bearing:
- Spin the hub and listen for grinding noises.
- If the bearing shows signs of wear, remove it for replacement.
Replace Bearing:
- Use a bearing puller to remove the old bearing.
- Install the new bearing using a press, ensuring it is seated correctly.

4. Check Suspension Components

Inspect Control Arm Bushings:
- Visually check for cracks or wear on the bushings.
- Replace if necessary by unbolting the control arm from the chassis.
Examine Shock Absorbers:
- Check for leaks or physical damage.
- Replace if worn using the appropriate tools to unbolt and remove.