why does my Volvo XC60 536 (2017-Present) make a loud noise when turning

Volvo XC60 536 (2017-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

551 words

Problem Statement

Discover how to diagnose and fix loud noise when turning in Volvo XC60. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under the vehicle.
•Disconnect the battery before working on electrical components to avoid short circuits.

Symptoms

•Loud grinding or popping noise when turning
•Increased steering effort or resistance
•Vibration in the steering wheel during turns
•Uneven tire wear observed
•Fluid leaks under the vehicle (potentially from power steering)

Diagnostic Steps

1
Inspect the power steering fluid level and condition; top up or replace if necessary.
2
Check for visible damage or wear in the suspension components (e.g., control arms, bushings).
3
Listen for the source of the noise while turning the steering wheel at a standstill.
4
Inspect the wheel bearings for play by jacking up the car and shaking the wheel.
5
Examine the CV joints and boots for damage or excessive play.
6
Check tire condition and pressure to rule out any issues related to tires.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Funnel
•Bearing puller

Parts Required

•Power steering fluid
•Control arms or bushings (if needed)
•Wheel bearings (if applicable)
•CV joint or axle assembly (if applicable)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition; top up or replace if necessary.
2
Check for visible damage or wear in the suspension components (e.g., control arms, bushings).
3
Listen for the source of the noise while turning the steering wheel at a standstill.
4
Inspect the wheel bearings for play by jacking up the car and shaking the wheel.
5
Examine the CV joints and boots for damage or excessive play.
6
Check tire condition and pressure to rule out any issues related to tires.

Solution

1. Preparation

Gather tools and parts required for the repair.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery if working on electronic components.

2. Inspect and Replace Power Steering Fluid

Tools Required: Funnel, power steering fluid
Inspect the power steering fluid reservoir for low levels.
If low, add the appropriate type of power steering fluid as per the owner's manual.
If fluid is dirty, consider flushing the system.

3. Replace Worn Suspension Components

Tools Required: Socket set, torque wrench, jack stands
Safely lift the vehicle and remove the wheel to access the suspension.
Remove any damaged control arms or bushings by unbolting them from the chassis and suspension.
Install new components, ensuring all bolts are torqued to manufacturer specifications.

4. Replace Wheel Bearings (if applicable)

Tools Required: Bearing puller, socket set, torque wrench
If bearings are found to be faulty, remove the wheel hub assembly.
Use a bearing puller to extract the old wheel bearings.
Install new bearings and reassemble the hub, ensuring proper torque on all bolts.

5. Inspect and Replace CV Joints (if applicable)

Tools Required: Socket set, jack stands
Inspect CV joints for any tear in the rubber boot or excessive play.
If damaged, remove the axle from the transmission and replace the CV joint or axle assembly as needed.