why does my Volkswagen Tiguan make a knocking sound when I accelerate?

Volkswagen Tiguan Second Generation (2018-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

517 words

Problem Statement

Learn how to diagnose and fix knocking sounds during acceleration in Volkswagen Tiguan. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before performing any work.

Symptoms

•Knocking noise when accelerating
•Noise intensifies with increased speed
•Vibration felt in the steering wheel
•Loss of power during acceleration
•Possible check engine light illumination

Diagnostic Steps

1
Inspect the engine mounts for wear or damage.
2
Check the transmission mounts for signs of failure.
3
Examine the CV joints for wear and tear.
4
Perform a visual inspection of the suspension components.
5
Scan for error codes using an OBD-II scanner.
6
Test drive the vehicle to replicate the noise and pinpoint its origin.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Jack and jack stands
•Lug wrench
•OBD-II scanner

Parts Required

•Engine mounts
•Transmission mounts
•CV joint or axle assembly
•Suspension bushings (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the engine mounts for wear or damage.
2
Check the transmission mounts for signs of failure.
3
Examine the CV joints for wear and tear.
4
Perform a visual inspection of the suspension components.
5
Scan for error codes using an OBD-II scanner.
6
Test drive the vehicle to replicate the noise and pinpoint its origin.

Solution

1. Preparation

Gather all necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety.

2. Inspect and Replace Engine and Transmission Mounts

Engine Mounts:
1. Use a socket set to remove the bolts securing the engine mounts.
2. Lift the engine slightly using a jack with a block of wood to support it.
3. Remove the old mounts and install new ones, ensuring proper alignment.
4. Torque the bolts to the manufacturer’s specifications (typically 25-35 ft-lbs).
Transmission Mounts:
1. Locate the transmission mount and remove the bolts using a socket set.
2. Support the transmission with a jack.
3. Remove the old mount and replace it with a new one.
4. Reinstall the bolts and torque to specifications (often around 30-40 ft-lbs).

3. Inspect and Replace CV Joints

Lift the vehicle and securely place it on jack stands.
Remove the front wheels using a lug wrench.
Inspect the CV joints for any visible cracks or grease leakage.
If damaged, remove the axle nut and detach the CV joint from the wheel hub.
Replace the CV joint or entire axle assembly as necessary.
Reinstall the wheel and torque the lug nuts to specifications (usually 85-100 ft-lbs).

4. Inspect Suspension Components

Visually inspect the control arms, bushings, and struts for any signs of wear or damage.
If any components are found to be defective, replace them using appropriate tools.
Ensure all fasteners are torqued to the manufacturer’s specifications.