why does my Volkswagen Tiguan make a grinding noise during turns

Volkswagen Tiguan Second Generation (2018-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

509 words

Problem Statement

Learn how to diagnose and fix grinding noise during turns in Volkswagen Tiguan. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery when working on electrical components.
•Allow the vehicle to cool before working on the suspension or drivetrain.

Symptoms

•Grinding noise when turning the steering wheel
•Increased resistance in the steering when turning
•Vibration in the steering wheel
•Noise may vary with speed or steering angle
•Potential clunking sound in addition to grinding

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible wear or damage on the CV joints and boots.
3
Examine the suspension components for any signs of damage or wear.
4
Test drive the vehicle to replicate the noise while making tight turns.
5
Use a mechanic's stethoscope to pinpoint the source of the grinding noise.
6
Inspect wheel bearings for play or roughness.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Floor jack
•Jack stands
•Socket set
•Torque wrench
•Bearing puller
•Bearing press

Parts Required

•CV joint assembly (if damaged)
•Wheel bearings (if faulty)
•Suspension components (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible wear or damage on the CV joints and boots.
3
Examine the suspension components for any signs of damage or wear.
4
Test drive the vehicle to replicate the noise while making tight turns.
5
Use a mechanic's stethoscope to pinpoint the source of the grinding noise.
6
Inspect wheel bearings for play or roughness.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a flat surface and the parking brake is engaged.

2. Lift the Vehicle

Use a jack to lift the front of the vehicle and secure it with jack stands.
Tools Required: Floor jack, jack stands.

3. Inspect and Replace CV Joints (if necessary)

Inspection:
- Remove the wheel to access the CV joint.
- Check for torn boots or grease leakage.
Replacement:
- If damaged, remove the axle nut using a socket wrench.
- Disconnect the CV joint from the wheel hub.
- Replace with a new CV joint, ensuring proper alignment and securing the axle nut to the manufacturer's torque specifications (typically around 30-50 ft-lbs).
Tools Required: Socket set, torque wrench.

4. Check and Tighten Suspension Components

Inspect all suspension components for looseness or wear.
Tighten any loose bolts to the manufacturer's specifications.
Replace any damaged components, such as control arms or bushings.

5. Inspect and Replace Wheel Bearings (if necessary)

Spin the hub to check for roughness or play.
If faulty, remove the hub assembly and replace the wheel bearing using a bearing press or appropriate tools.
Reassemble and torque to specifications.
Tools Required: Bearing puller, bearing press, socket set.