why is my Volkswagen Tiguan Second Generation (2018-present) oil light on

Volkswagen Tiguan 2nd Gen (2018-Present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

571 words

Problem Statement

Learn how to diagnose and fix the oil light issue on your Volkswagen Tiguan (2018-present). Step-by-step guide with symptoms, diagnostic steps, and solutions.

Affected Component

Engine

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the oil cap or removing the oil filter.

Symptoms

•Oil pressure warning light on the dashboard
•Engine oil level may be low
•Possible unusual engine noises (ticking or knocking)
•Decreased engine performance
•Oil leaks under the vehicle

Diagnostic Steps

1
Check the engine oil level using the dipstick.
2
Inspect for any visible oil leaks around the engine and under the vehicle.
3
Scan the vehicle's onboard computer for any oil pressure-related error codes using an OBD-II scanner.
4
Verify the oil condition (color and viscosity) by checking the oil on the dipstick.
5
Inspect the oil filter for proper installation and any signs of damage.
6
Check the oil pressure sending unit for proper function and leaks.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Oil filter wrench
•Socket set
•Multimeter
•Oil catch pan

Parts Required

•Engine oil (5W-30 synthetic)
•Oil filter
•Oil pressure sending unit (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the engine oil level using the dipstick.
2
Inspect for any visible oil leaks around the engine and under the vehicle.
3
Scan the vehicle's onboard computer for any oil pressure-related error codes using an OBD-II scanner.
4
Verify the oil condition (color and viscosity) by checking the oil on the dipstick.
5
Inspect the oil filter for proper installation and any signs of damage.
6
Check the oil pressure sending unit for proper function and leaks.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is on a flat surface and the engine is cool.
Disconnect the battery to prevent any electrical issues.

2. Check and Top Off Engine Oil

Sub-steps:
1. Remove the dipstick and wipe it clean.
2. Reinsert the dipstick and remove it again to check the oil level.
3. If low, add the appropriate oil (5W-30 synthetic oil recommended).
4. Recheck the oil level after adding oil to ensure it is within the acceptable range.

3. Inspect and Replace Oil Filter (if necessary)

Tools Required: Oil filter wrench, socket set.
Sub-steps:
1. Place an oil catch pan under the oil filter.
2. Use the oil filter wrench to remove the old oil filter.
3. Lubricate the rubber O-ring on the new filter with a little fresh oil.
4. Install the new oil filter by hand until snug, then tighten with the wrench (do not over-tighten).

4. Test Oil Pressure Sending Unit

Tools Required: Multimeter.
Sub-steps:
1. Locate the oil pressure sending unit on the engine (refer to service manual for exact location).
2. Disconnect the electrical connector and use a multimeter to test for proper voltage.
3. Replace the oil pressure sending unit if it fails the test.

5. Reset Oil Light

Sub-steps:
1. Turn the ignition on without starting the engine.
2. Navigate to the vehicle settings in the infotainment system.
3. Find the option to reset the oil change interval or oil light.
4. Confirm the reset and turn off the ignition.