why is my Volkswagen Tiguan Second Generation (2018-present) making a clicking noise when turning

Volkswagen Tiguan 2nd Gen (2018-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

519 words

Problem Statement

Learn how to diagnose and fix the clicking noise when turning in your Volkswagen Tiguan. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the vehicle to cool before performing any repairs on brake components.

Symptoms

•Clicking noise during turns
•Noise occurs more prominently when turning sharply
•Possible vibration in the steering wheel
•Increased play in the steering
•Uneven tire wear (if observed over time)

Diagnostic Steps

1
Inspect front tires for any signs of damage or uneven wear.
2
Check the wheel bearings for play or noise by spinning the wheel and feeling for roughness.
3
Examine the CV joints and boots for any visible damage or grease leakage.
4
Lift the vehicle and perform a visual inspection of the steering and suspension components for wear or damage.
5
Test the steering rack for any unusual movement or noise when turning the steering wheel.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Lug wrench
•Torque wrench
•CV joint puller (if necessary)
•Bearing puller (if necessary)
•Basic hand tools (sockets, wrenches)

Parts Required

•CV joint or CV axle (if damaged)
•Wheel bearings (if worn)
•New axle nut (recommended for replacement)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect front tires for any signs of damage or uneven wear.
2
Check the wheel bearings for play or noise by spinning the wheel and feeling for roughness.
3
Examine the CV joints and boots for any visible damage or grease leakage.
4
Lift the vehicle and perform a visual inspection of the steering and suspension components for wear or damage.
5
Test the steering rack for any unusual movement or noise when turning the steering wheel.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a flat surface and the engine is off.
Disconnect the battery for safety.

2. Inspect and Replace CV Joint

Sub-steps:
1. Lift the front of the vehicle using a jack and secure it with jack stands.
2. Remove the wheel on the side where the noise is present using a lug wrench.
3. Inspect the outer CV joint for torn boots or excessive play.
4. If damaged, remove the CV axle by unbolting it from the wheel hub and transmission.
5. Replace the CV joint or entire axle with a new one, ensuring to apply the correct torque (typically around 33 lb-ft for the axle nut).

3. Inspect and Replace Wheel Bearings

Sub-steps:
1. If the wheel bearings are suspected, remove the brake caliper and rotor.
2. Inspect the wheel bearing assembly for signs of wear or noise.
3. If replacement is needed, remove the bearing using a bearing puller.
4. Install a new wheel bearing and reassemble the brake components.

4. Reassemble and Test

Sub-steps:
1. Reattach the wheel and lower the vehicle back to the ground.
2. Reconnect the battery.
3. Test drive the vehicle to ensure the clicking noise is resolved.