my Volkswagen Tiguan Second Generation (2018-present) wipers are not working what could be the issue

Volkswagen Tiguan 2nd Gen (2018-Present)

Error Codes

1-3 hours

Time

medium

Difficulty

medium

Severity

3 min read

490 words

Problem Statement

Learn how to diagnose and fix windshield wipers not working on Volkswagen Tiguan Second Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Electrical

Estimated Time

1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components to prevent shocks or short circuits.

Symptoms

•Windshield wipers do not operate at all
•Wiper motor makes a noise when activated
•Wipers are stuck in one position
•Intermittent operation of the wipers
•Wiper fluid not spraying

Diagnostic Steps

1
Check the wiper switch for proper operation by toggling through all settings.
2
Inspect the fuse box for a blown fuse related to the wiper system.
3
Use a multimeter to test the wiper motor for continuity and proper voltage.
4
Examine the wiper linkage for any disconnections or damage.
5
Check the condition of the wiper blades for wear or obstruction.
6
Inspect the wiring harness for any signs of damage or corrosion.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Flathead screwdriver
•Socket set
•Multimeter
•Pliers

Parts Required

•Wiper motor (if needed)
•Wiper blades (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the wiper switch for proper operation by toggling through all settings.
2
Inspect the fuse box for a blown fuse related to the wiper system.
3
Use a multimeter to test the wiper motor for continuity and proper voltage.
4
Examine the wiper linkage for any disconnections or damage.
5
Check the condition of the wiper blades for wear or obstruction.
6
Inspect the wiring harness for any signs of damage or corrosion.

Solution

1. Preparation

Gather tools and parts needed.
Ensure the vehicle is parked on a flat surface and the ignition is off.
Disconnect the battery to ensure safety.

Tools Required:

Flathead screwdriver
Socket set
Multimeter
Pliers

2. Inspect and Replace Fuse

Locate the fuse box, typically found under the dashboard or in the engine compartment.
Remove the cover and identify the wiper fuse (refer to the diagram inside the fuse box).
Pull the fuse using pliers and inspect for any breaks or damage.
If blown, replace with a fuse of the same amperage.

3. Test Wiper Motor

Reconnect the battery and use a multimeter to check voltage at the wiper motor connector while the wiper switch is activated.
If voltage is present but the motor does not operate, proceed to replace the wiper motor.

4. Replace Wiper Motor (if needed)

Remove the wiper arms by loosening the securing nuts using a socket set.
Disconnect the wiper motor harness.
Remove the mounting bolts securing the motor to the vehicle and take out the motor.
Install the new motor by reversing the removal steps and ensure to reconnect the harness.

5. Reassemble Wiper Arms

Position the wiper arms back onto the motor splines.
Secure with the nuts and ensure they are tightened to the manufacturer's torque specifications.