why does my Volkswagen Golf MK7.5 (2020-Present) make a loud noise when starting

Volkswagen Golf MK7.5 (2020-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

514 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Diagnose and fix loud noise when starting Volkswagen Golf MK7.5. Step-by-step guide with symptoms, diagnostic steps, tools, and repair instructions.

Affected Component

Electrical

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before inspecting components.

Symptoms

•Loud cranking noise when the engine starts
•Possible grinding sound during engine turnover
•Intermittent clicking noise instead of a smooth start
•Engine may take longer to start than usual
•No dashboard warning lights illuminated

Diagnostic Steps

1
Check the battery voltage using a multimeter to ensure it is fully charged (12.6 volts or higher).
2
Inspect battery terminals for corrosion or loose connections.
3
Test the starter motor by checking for proper engagement and operation.
4
Listen for unusual sounds from the starter while cranking the engine.
5
Inspect the flywheel for any signs of damage or missing teeth.
6
Check for any loose or damaged engine mounts that may contribute to noise.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Multimeter
•Socket set
•Torque wrench
•Screwdriver set

Parts Required

•New battery (if needed)
•New starter motor (if needed)
•New engine mounts (if needed)
•Flywheel (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the battery voltage using a multimeter to ensure it is fully charged (12.6 volts or higher).
2
Inspect battery terminals for corrosion or loose connections.
3
Test the starter motor by checking for proper engagement and operation.
4
Listen for unusual sounds from the starter while cranking the engine.
5
Inspect the flywheel for any signs of damage or missing teeth.
6
Check for any loose or damaged engine mounts that may contribute to noise.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a flat surface and the engine is cool.
Disconnect the negative terminal of the battery to ensure safety.

2. Battery Inspection and Replacement

Sub-step 1: If the battery is weak, replace it. Remove the positive terminal first, followed by the negative terminal.
Sub-step 2: Remove the battery hold-down bracket and lift the battery out carefully.
Sub-step 3: Install the new battery in reverse order, ensuring tight connections and securing the hold-down.

3. Starter Motor Inspection and Replacement

Sub-step 1: Locate the starter motor (usually near the transmission).
Sub-step 2: Disconnect the electrical connectors and the mounting bolts using a socket set.
Sub-step 3: Remove the starter motor and inspect for wear or damage.
Sub-step 4: Install the new starter motor by reversing the removal steps, ensuring all connections are secure.

4. Flywheel Inspection

Sub-step 1: If noise persists, check the flywheel. Remove the transmission cover if necessary to access the flywheel.
Sub-step 2: Inspect for broken teeth or damage; replace if necessary.
Sub-step 3: Reinstall the transmission cover if removed.

5. Engine Mount Inspection

Sub-step 1: Check the engine mounts for any signs of wear or damage.
Sub-step 2: Replace any damaged engine mounts as necessary by removing the securing bolts and installing the new mounts.