why does my Volkswagen Golf MK7.5 (2020-Present) make a grinding noise when turning

Volkswagen Golf MK7.5 (2020-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

534 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix grinding noise when turning in Volkswagen Golf MK7.5. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Use jack stands when lifting the vehicle to prevent accidents.

Symptoms

•Grinding noise when turning the steering wheel
•Vibration in the steering wheel
•Difficulty steering, especially at low speeds
•Unusual wear on tires
•Clunking sounds when going over bumps

Diagnostic Steps

1
Inspect the steering components for visible damage or wear.
2
Check the power steering fluid level and condition.
3
Examine the wheel bearings for play or grinding sounds.
4
Inspect the CV joints for any signs of damage or lubricant leakage.
5
Test for proper installation and condition of the brake components.
6
Lift the vehicle and check for any loose or damaged suspension parts.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Pry bar
•CV joint puller
•Bearing puller
•Funnel

Parts Required

•CV joint assembly (if applicable)
•Wheel bearings (if applicable)
•Power steering fluid (if applicable)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the steering components for visible damage or wear.
2
Check the power steering fluid level and condition.
3
Examine the wheel bearings for play or grinding sounds.
4
Inspect the CV joints for any signs of damage or lubricant leakage.
5
Test for proper installation and condition of the brake components.
6
Lift the vehicle and check for any loose or damaged suspension parts.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Ensure the vehicle is parked on a flat surface and set the parking brake.
Disconnect the battery if working on electronic components.

2. Inspect and Replace CV Joints

Tools Required: Socket set, torque wrench, pry bar, CV joint puller.
Remove the wheel and tire to access the CV joint.
Use a pry bar to check for play in the CV joint; if excessive, replace the joint.
To replace, remove the axle nut and disconnect the joint from the transmission side.
Install the new CV joint and torque the axle nut to manufacturer specifications (typically around 200 Nm).

3. Check and Replace Wheel Bearings

Tools Required: Bearing puller, socket set, torque wrench.
Remove the brake caliper and rotor to access the wheel bearing.
Use a bearing puller to remove the old bearing.
Install the new bearing, ensuring it is seated properly, and reassemble the brake components.
Torque the brake components to manufacturer specifications.

4. Inspect and Refill Power Steering Fluid

Tools Required: Funnel, shop towels.
Locate the power steering fluid reservoir.
Check the fluid level; if low, top it off with the correct type of fluid (refer to owner’s manual).
If the fluid is contaminated, consider a full flush and replacement.

5. Check Suspension Components

Tools Required: Socket set, pry bar.
Inspect the control arms, bushings, and struts for wear or damage.
Replace any worn components as necessary, ensuring proper torque on all bolts.