why does my Volkswagen Golf MK7.5 (2020-Present) make a clicking noise when turning

Volkswagen Golf MK7.5 (2020-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

530 words

Problem Statement

Learn how to diagnose and fix the clicking noise when turning in your Volkswagen Golf MK7.5. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow the vehicle to cool before working on brakes or suspension components.

Symptoms

•Clicking noise when turning the steering wheel
•Noise may increase in volume during sharper turns
•Possible vibration felt through the steering wheel
•No loss of steering control or handling issues
•Noise present when driving at low speeds

Diagnostic Steps

1
Inspect the CV joints for signs of wear or damage.
2
Check the condition of the wheel bearings for any play or roughness.
3
Examine the suspension components, including control arms and bushings, for wear or damage.
4
Verify the tightness of the lug nuts on the affected wheel.
5
Perform a visual inspection of the brake components to rule out interference.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Hydraulic jack
•Jack stands
•Socket set
•Bearing puller
•Torque wrench
•Screwdriver set

Parts Required

•CV joint (if damaged)
•Wheel bearing (if worn)
•Replacement suspension components (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joints for signs of wear or damage.
2
Check the condition of the wheel bearings for any play or roughness.
3
Examine the suspension components, including control arms and bushings, for wear or damage.
4
Verify the tightness of the lug nuts on the affected wheel.
5
Perform a visual inspection of the brake components to rule out interference.

Solution

1. Preparation

Gather required tools and parts.
Ensure the vehicle is parked on a level surface, and engage the parking brake.
Disconnect the battery before starting work on electrical components.

2. Inspect and Replace CV Joints

Sub-steps:
1. Lift the vehicle using a hydraulic jack and secure it with jack stands.
2. Remove the wheel on the side where the clicking noise is present using a socket set.
3. Inspect the outer CV joint boot for tears or leaking grease.
4. If damaged, remove the CV joint by unbolting it from the hub assembly.
5. Replace the CV joint with a new unit, ensuring proper alignment and securing it with the specified torque (typically 30-40 ft-lbs).
6. Reinstall the wheel and lower the vehicle.

3. Check and Replace Wheel Bearings

Sub-steps:
1. With the wheel removed, check for play in the wheel bearing by grasping the top and bottom of the tire and rocking it.
2. If play is detected, remove the brake caliper and rotor to access the wheel hub.
3. Remove the wheel bearing using a bearing puller.
4. Install a new wheel bearing, ensuring it is pressed in correctly.
5. Reassemble the brake components and wheel.

4. Inspect Suspension Components

Sub-steps:
1. Visually inspect control arms, bushings, and struts for wear or damage.
2. Replace any worn or damaged components with new parts, following manufacturer specifications.
3. Reassemble any removed components and ensure all bolts are torqued to the specified values.