my Volkswagen Golf MK7.5 (2020-Present) is showing a P0720 code

Volkswagen Golf MK7.5 (2020-Present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

Error Code: P0720

3 min read

475 words

Problem Statement

Learn how to diagnose and fix P0720 vehicle speed sensor issues in Volkswagen Golf MK7.5. Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0720

Affected Component

Transmission

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before working near the transmission.

Symptoms

•Check engine light illuminated
•Erratic speedometer readings
•Transmission shifting issues
•Poor acceleration or hesitation
•Increased fuel consumption
•Loss of cruise control functionality

Diagnostic Steps

1
Scan the vehicle's OBD-II system for additional error codes.
2
Inspect the vehicle speed sensor connector for any loose or damaged wiring.
3
Test the vehicle speed sensor with a multimeter to check for proper resistance.
4
Check the wiring harness for continuity between the vehicle speed sensor and the engine control module (ECM).
5
Inspect the sensor mounting location for any debris or damage that may affect operation.
6
Verify the vehicle's battery voltage and ground connections to ensure proper electrical function.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Torque wrench

Parts Required

•Vehicle speed sensor
•O-ring or seal (if applicable)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's OBD-II system for additional error codes.
2
Inspect the vehicle speed sensor connector for any loose or damaged wiring.
3
Test the vehicle speed sensor with a multimeter to check for proper resistance.
4
Check the wiring harness for continuity between the vehicle speed sensor and the engine control module (ECM).
5
Inspect the sensor mounting location for any debris or damage that may affect operation.
6
Verify the vehicle's battery voltage and ground connections to ensure proper electrical function.

Solution

1. Preparation

Gather necessary tools and parts.
Disconnect the negative battery terminal to prevent electrical shorts.
Ensure the vehicle is on a level surface and securely supported.

2. Remove the Vehicle Speed Sensor

Locate the vehicle speed sensor, typically near the transmission.
Disconnect the electrical connector from the sensor.
Remove the retaining bolt(s) securing the sensor using a socket set.
Carefully pull the sensor out from its housing.

3. Inspect and Clean

Inspect the sensor for physical damage or wear.
Clean the sensor mounting area to remove any debris or old sealant.
Check the O-ring or seal for wear and replace if necessary.

4. Install the New Sensor

Apply a light coat of engine oil to the new sensor O-ring (if applicable).
Insert the new vehicle speed sensor into the mounting hole and secure it with the retaining bolt(s).
Reconnect the electrical connector to the sensor.

5. Reconnect Battery and Test

Reconnect the negative battery terminal.
Start the vehicle and allow it to reach operating temperature.
Clear the fault codes using an OBD-II scanner and test drive the vehicle to monitor for any return of the P0720 code.