my Volkswagen Golf MK7.5 (2020-Present) has a clicking noise when I turn

Volkswagen Golf MK7.5 (2020-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

502 words

Problem Statement

Learn how to diagnose and fix clicking noise when turning in Volkswagen Golf MK7.5. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical components.
•Allow the vehicle to cool down before starting any maintenance work.

Symptoms

•Clicking noise during turns
•Noise increases with sharper turns
•Possible vibration in the steering wheel
•Limited steering response
•Potential clunking noise when driving over bumps

Diagnostic Steps

1
Inspect the front suspension components for any visible damage or wear, including control arms and bushings.
2
Check the CV joints for signs of wear or leakage, as they can cause clicking noises when turning.
3
Examine the steering rack and tie rod ends for any looseness or play.
4
Perform a road test to replicate the noise and determine under which conditions it occurs.
5
Use an OBD-II scanner to check for any related trouble codes that may point to steering or suspension issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Jack and jack stands
•Torque wrench
•Breaker bar
•OBD-II scanner

Parts Required

•CV joint assembly (if damaged)
•Bushings (if worn)
•Suspension control arms (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front suspension components for any visible damage or wear, including control arms and bushings.
2
Check the CV joints for signs of wear or leakage, as they can cause clicking noises when turning.
3
Examine the steering rack and tie rod ends for any looseness or play.
4
Perform a road test to replicate the noise and determine under which conditions it occurs.
5
Use an OBD-II scanner to check for any related trouble codes that may point to steering or suspension issues.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Wear safety gloves and goggles.

2. Inspect and Replace CV Joints

Sub-steps:
1. Raise the front of the vehicle using a jack and secure it with jack stands.
2. Remove the front wheels using a socket set.
3. Visually inspect the CV joint boots for tears or grease leakage.
4. If damaged, remove the axle nut using a breaker bar.
5. Disconnect the CV joint from the hub by removing the retaining bolts.
6. Replace the CV joint with a new one, ensuring it is properly seated.
7. Reassemble by reversing the disassembly steps and torque the axle nut to manufacturer specifications (usually around 180-220 Nm).

3. Inspect and Replace Suspension Components

Sub-steps:
1. With the vehicle still lifted, inspect the control arms and bushings for wear.
2. If any bushings are cracked or degraded, remove the control arm bolts and replace the bushings.
3. Reinstall the control arms, ensuring all bolts are torqued to manufacturer specifications.
4. Check for any loose bolts on the steering rack and tighten if necessary.

4. Test Drive

After repairs, lower the vehicle and perform a test drive to ensure the clicking noise is resolved.