how to fix my Volkswagen Golf MK7.5 (2020-Present) if it shakes during braking

Volkswagen Golf MK7.5 (2020-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

515 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix shaking during braking in Volkswagen Golf MK7.5. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery when working on brake systems to avoid accidental brake activation.
•Ensure the vehicle is securely lifted and supported before working underneath.

Symptoms

•Vibration in the steering wheel during braking
•Shaking felt through the brake pedal
•Uneven wear on brake pads
•Increased stopping distance
•Possible noise from the brakes

Diagnostic Steps

1
Inspect the brake rotors for warping or uneven wear using a run-out gauge.
2
Check the brake pads for wear and ensure they are properly seated.
3
Examine the wheel bearings for play or damage.
4
Inspect tire condition and balance; look for bulges or uneven wear.
5
Check for proper wheel alignment and suspension components for wear or damage.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Lug wrench
•Jack and jack stands
•Torque wrench
•Run-out gauge
•Basic hand tools

Parts Required

•Brake rotors
•Brake pads

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the brake rotors for warping or uneven wear using a run-out gauge.
2
Check the brake pads for wear and ensure they are properly seated.
3
Examine the wheel bearings for play or damage.
4
Inspect tire condition and balance; look for bulges or uneven wear.
5
Check for proper wheel alignment and suspension components for wear or damage.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a flat surface and engage the parking brake.
Wear safety gloves and goggles.

2. Remove Wheel

Use a lug wrench to loosen the lug nuts on the affected wheel.
Raise the vehicle using a jack and secure it with jack stands.
Completely remove the lug nuts and take off the wheel.

3. Inspect and Replace Brake Components

Inspect Brake Rotors:
- Use a run-out gauge to check for warping (should not exceed manufacturer specifications).
- If warped, proceed to replace the rotors.
Replace Brake Pads:
- Remove the caliper by unscrewing the caliper bolts (usually 13-15mm).
- Slide the caliper off and remove the old brake pads.
- Install new brake pads, ensuring they are properly aligned and seated.
Reinstall Caliper:
- Slide the caliper over the new pads and secure it with the caliper bolts. Torque to manufacturer specifications (typically around 25-30 Nm).

4. Wheel Reinstallation

Place the wheel back onto the hub.
Hand-tighten the lug nuts to hold the wheel in place.
Lower the vehicle from the jack stands and torque the lug nuts to manufacturer specifications (usually 100-120 Nm).

5. Test Drive

After reassembling, perform a test drive to check for vibrations during braking.
Monitor brake performance and listen for unusual noises.