how to fix electric power steering problems in Volkswagen Golf MK7.5 (2020-Present)

Volkswagen Golf MK7.5 (2020-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

569 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix electric power steering problems in Volkswagen Golf MK7.5. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems to prevent short circuits or electrical shocks.

Symptoms

•Power steering warning light illuminated on the dashboard
•Increased steering effort, especially at low speeds
•Intermittent or complete loss of power steering assist
•Noisy steering operation, such as whining or grinding sounds
•Possible steering wheel vibration or play

Diagnostic Steps

1
Scan the vehicle for error codes using an OBD-II scanner to identify any faults related to the power steering system.
2
Inspect the power steering fuse and relay for any signs of damage or failure.
3
Check the condition of the electric power steering motor and wiring for any visible damage or disconnections.
4
Verify the battery voltage and charging system as low voltage can affect power steering functions.
5
Test the steering angle sensor for proper operation and calibration.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Torque wrench
•Steering wheel puller

Parts Required

•Power steering fuse (if blown)
•Electric power steering motor (if faulty)
•Wiring connectors (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle for error codes using an OBD-II scanner to identify any faults related to the power steering system.
2
Inspect the power steering fuse and relay for any signs of damage or failure.
3
Check the condition of the electric power steering motor and wiring for any visible damage or disconnections.
4
Verify the battery voltage and charging system as low voltage can affect power steering functions.
5
Test the steering angle sensor for proper operation and calibration.

Solution

1. Preparation

Tools Needed: OBD-II scanner, multimeter, socket set, torque wrench, steering wheel puller (if necessary).
Disconnect the negative battery terminal to avoid electrical shorts during repairs.

2. Inspect and Replace Power Steering Fuse

Locate the fuse box (usually under the dashboard or in the engine bay).
Remove the cover and locate the power steering fuse.
Check the fuse; if blown, replace it with a new one of the same amperage.
Reconnect the battery and test the steering system.

3. Check and Repair Wiring

Visually inspect the wiring harness connected to the power steering motor for frays or loose connections.
Use a multimeter to check for continuity in the wiring.
Repair or replace damaged wires as necessary, ensuring all connections are secure.

4. Replace or Repair Power Steering Motor

If the motor is faulty, disconnect the wiring harness from the motor.
Remove the mounting bolts securing the power steering motor using the socket set.
Install the new or repaired motor by reversing the removal steps, ensuring it is tightened to the manufacturer's torque specifications.
Reconnect the wiring harness.

5. Calibration of Steering Angle Sensor

After repairs, use the OBD-II scanner to reset any fault codes.
Follow the manufacturer's procedure to calibrate the steering angle sensor, often accessible via the scanner's diagnostic functions.
Test drive the vehicle to ensure proper steering operation.