why is my Volkswagen Golf MK7 (2015-2019) consuming too much oil

Volkswagen Golf MK7 (2015-2019)

Error Codes

2-4 hours

Time

hard

Difficulty

high

Severity

3 min read

571 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix excessive oil consumption in Volkswagen Golf MK7 (2015-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool before opening the oil cap or working on engine components.

Symptoms

•Engine oil warning light illuminated
•Frequent need to add oil between changes
•Blue smoke from the exhaust during acceleration
•Rough engine idle or misfires
•Increased engine noise
•Strong smell of burning oil

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for any related engine fault codes.
2
Inspect the engine oil level and condition to determine if it is contaminated or excessively low.
3
Check for external oil leaks around the engine, oil pan, valve cover, and gaskets.
4
Perform a compression test on the cylinders to identify potential internal leaks or wear.
5
Inspect the PCV (Positive Crankcase Ventilation) system for blockages or malfunctions.
6
Review service history for previous oil changes and check if the correct oil type and viscosity were used.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Gasket scraper
•Pliers
•Engine hoist

Parts Required

•Valve cover gasket
•Oil pan gasket
•PCV valve
•Engine rebuild kit

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for any related engine fault codes.
2
Inspect the engine oil level and condition to determine if it is contaminated or excessively low.
3
Check for external oil leaks around the engine, oil pan, valve cover, and gaskets.
4
Perform a compression test on the cylinders to identify potential internal leaks or wear.
5
Inspect the PCV (Positive Crankcase Ventilation) system for blockages or malfunctions.
6
Review service history for previous oil changes and check if the correct oil type and viscosity were used.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is cool.
Disconnect the battery for safety.

2. Address Oil Leaks

Tools Required: Socket set, torque wrench, gasket scraper
Instructions:
1. Inspect the valve cover and oil pan for leaks.
2. Remove any components obstructing access (e.g., air intake, engine covers).
3. Clean the mounting surfaces thoroughly with a gasket scraper.
4. Replace any damaged gaskets or seals.
5. Reinstall all components and torque to manufacturer specifications.

3. Replace PCV Valve (if faulty)

Tools Required: Pliers, socket set
Instructions:
1. Locate the PCV valve, typically on the valve cover or intake manifold.
2. Disconnect the hoses attached to the PCV valve using pliers.
3. Remove the old PCV valve.
4. Install a new PCV valve, ensuring a snug fit.
5. Reconnect the hoses.

4. Perform Engine Rebuild (if internal issues found)

Tools Required: Engine hoist, complete engine rebuild kit
Instructions:
1. If compression tests indicate low compression, consider removing the engine for a rebuild.
2. Disassemble the engine, replacing worn piston rings, cylinder gaskets, and bearings as necessary.
3. Reassemble the engine according to manufacturer specifications.
4. Reinstall the engine and reconnect all components.