why does my Volkswagen Golf MK6 (2009-2014) make a clicking sound while turning?

Volkswagen Golf MK7 (2015-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

559 words

Problem Statement

Learn how to diagnose and fix the clicking sound while turning in Volkswagen Golf MK6 (2009-2014). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under a lifted vehicle.
•Allow the engine to cool before working on any components near it.

Symptoms

•Clicking noise when turning the steering wheel, especially during sharp turns
•Noise may be more pronounced when turning left or right
•Possible vibration felt in the steering wheel or front end
•Decreased steering response or handling
•Potential loss of traction or stability in corners

Diagnostic Steps

1
Inspect the wheel and tire condition for any visible damage or foreign objects.
2
Check the CV joints for wear or damage, looking for torn boots or excessive play.
3
Listen for the sound with the vehicle on a lift while an assistant turns the steering wheel.
4
Examine the suspension components, including control arms and bushings, for wear or looseness.
5
Test drive the vehicle in a safe area while making tight turns to isolate the noise source.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Socket set
•Torque wrench
•Pry bar

Parts Required

•CV joint or CV axle (if damaged)
•Suspension bushings (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the wheel and tire condition for any visible damage or foreign objects.
2
Check the CV joints for wear or damage, looking for torn boots or excessive play.
3
Listen for the sound with the vehicle on a lift while an assistant turns the steering wheel.
4
Examine the suspension components, including control arms and bushings, for wear or looseness.
5
Test drive the vehicle in a safe area while making tight turns to isolate the noise source.

Solution

1. Preparation

Gather tools: jack, jack stands, socket set, torque wrench, and pry bar.
Ensure the vehicle is parked on a flat surface and the parking brake is engaged.
Disconnect the battery if working on electrical components.

2. Inspect and Replace CV Joints

Lift the Vehicle
- Use a jack to lift the front of the vehicle and secure it with jack stands.
Remove Wheel
- Using a socket set, remove the lug nuts and take off the front wheel for access to CV components.
Inspect CV Joint
- Check the outer and inner CV joints for any signs of damage, such as torn boots or excessive grease leakage.
- If damaged, proceed to replace the CV joint.
Remove CV Axle
- Remove the bolts securing the CV axle to the hub and differential.
- Use a pry bar to gently tap out the axle if it is stuck.
Install New CV Joint
- Insert the new CV joint and secure it to the hub and differential with the appropriate torque specifications (typically 30-50 ft-lbs, but check the service manual).

3. Inspect Suspension Components

Check Control Arms and Bushings
- Inspect control arms, ball joints, and bushings for wear or damage.
- Replace any worn or damaged components as necessary.
Reassemble
- Reattach the wheel and secure with lug nuts, tightening to the specified torque (usually around 90-100 ft-lbs).
- Lower the vehicle and reconnect the battery if it was disconnected.