my Volkswagen Golf MK6 (2009-2014) has a clicking sound when I turn left, what could it be?

Volkswagen Golf MK7 (2015-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

537 words

Problem Statement

Learn how to diagnose and fix the clicking sound when turning left in your Volkswagen Golf MK6. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands to secure the vehicle when working underneath.
•Disconnect the battery before performing electrical work or repairs.

Symptoms

•Clicking sound during left turns
•Possible vibration felt through the steering wheel
•Increased difficulty in steering response
•Noises may worsen with sharper turns or higher speeds
•Potential grease leakage near the wheel area

Diagnostic Steps

1
Inspect the outer CV joint for wear or damage.
2
Check the inner CV joint for any signs of excessive play.
3
Examine the suspension components (control arms, ball joints) for wear.
4
Look for any damaged or loose wheel bearings.
5
Test drive the vehicle to confirm the noise persists under various conditions.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Wheel chocks
•Socket set
•Torque wrench
•Pry bar
•CV joint grease
•Gloves

Parts Required

•New CV joint (if necessary)
•CV joint boot kit (if applicable)
•Axle nut (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the outer CV joint for wear or damage.
2
Check the inner CV joint for any signs of excessive play.
3
Examine the suspension components (control arms, ball joints) for wear.
4
Look for any damaged or loose wheel bearings.
5
Test drive the vehicle to confirm the noise persists under various conditions.

Solution

1. Preparation

Tools Required: Jack, jack stands, wheel chocks, socket set, torque wrench, pry bar, CV joint grease, and gloves.
Ensure the vehicle is on a flat surface and secure it with wheel chocks.
Disconnect the battery to ensure safety during the repair.

2. Lift the Vehicle

Use a jack to lift the front of the vehicle and secure it with jack stands.
Remove the front wheel on the side where the clicking noise occurs.

3. Inspect the CV Joint

Outer CV Joint:
- Remove any protective rubber boot if necessary.
- Inspect for torn boots and missing grease.
- Use a pry bar to check for play in the joint; if excessive, it should be replaced.
Inner CV Joint:
- Remove the axle from the transaxle.
- Inspect the inner CV joint for wear or damage.
- Check for any foreign debris or excessive play.

4. Replace the CV Joint (if necessary)

If the CV joint is damaged:
1. Remove the axle nut using the appropriate socket.
2. Disconnect the tie rod end and control arm if necessary to free the axle.
3. Replace the CV joint with a new one, ensuring it is properly greased.
4. Reinstall the axle and torque the axle nut to the manufacturer’s specifications.

5. Reassemble and Test

Reattach the wheel and lower the vehicle.
Reconnect the battery.
Test drive the vehicle to ensure the clicking sound has been resolved.