why does my Volkswagen Golf Eighth Generation (2020-present) make a clicking sound when turning

Volkswagen Golf Eighth Generation (2020-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

550 words

Problem Statement

Learn how to diagnose and fix the clicking sound when turning in your Volkswagen Golf. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow engine to cool before performing any repairs.

Symptoms

•Clicking noise during turns
•Noise increases with the speed of the turn
•Possible vibration felt in the steering wheel
•Difficulty steering or changes in steering response
•Check engine light may be illuminated

Diagnostic Steps

1
Inspect the front CV joints and boots for wear or damage.
2
Check the power steering fluid level and condition.
3
Examine the wheel bearings for play or noise.
4
Lift the vehicle and perform a visual inspection of the suspension components.
5
Test drive the vehicle to replicate the noise and identify the specific turning radius that causes it.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Socket set
•Torque wrench
•Screwdriver set
•CV joint grease

Parts Required

•New CV joint (if damaged)
•New wheel bearings (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front CV joints and boots for wear or damage.
2
Check the power steering fluid level and condition.
3
Examine the wheel bearings for play or noise.
4
Lift the vehicle and perform a visual inspection of the suspension components.
5
Test drive the vehicle to replicate the noise and identify the specific turning radius that causes it.

Solution

1. Preparation

Gather tools and materials needed for repair.
Tools Required:
- Jack and jack stands
- Socket set
- Torque wrench
- Screwdriver set
- CV joint grease (if applicable)

2. Inspect and Replace CV Joints

Lift the Vehicle: Use a jack to raise the front of the vehicle and secure it with jack stands.
Remove Wheel: Using a socket set, remove the wheel on the side where the noise is heard.
Check CV Boot: Inspect the CV boot for any tears or leaks. If damaged, the CV joint may need to be replaced.
Remove CV Joint:
- Disconnect the lower control arm from the knuckle (if necessary) to access the CV joint.
- Use appropriate tools to remove the CV joint from the transmission and axle.
Install New CV Joint:
- Lubricate the new CV joint with grease.
- Install the new CV joint into the axle and transmission, ensuring it is secured with the retaining clips.
Reassemble Components: Reattach the lower control arm to the knuckle and torque to manufacturer specifications (refer to repair manual for specific torque values).

3. Inspect and Replace Wheel Bearings

Remove Hub Assembly: If noise persists after CV joint replacement, remove the hub assembly from the vehicle.
Check Bearing Condition: Inspect the wheel bearings for wear or damage.
Replace Bearings: If necessary, press out the old bearings and press in new bearings using a bearing press tool.
Reinstall Hub Assembly: Reattach the hub assembly and torque to manufacturer specifications.