my Volkswagen Golf Eighth Generation (2020-present) remote start button not working what to do

Volkswagen Golf Eighth Generation (2020-present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

528 words

Problem Statement

Learn how to diagnose and fix the remote start issue in your Volkswagen Golf Eighth Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Electrical

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the vehicle battery if working on electrical systems to avoid shorts or shocks.

Symptoms

•Remote start button is unresponsive
•Vehicle does not start when remote start is activated
•Key fob battery may be weak or dead
•"Key not detected" warning on the dashboard
•Check engine light may be illuminated

Diagnostic Steps

1
Check the key fob battery level using a multimeter or by replacing it with a new battery.
2
Ensure the vehicle is in the correct mode for remote start (e.g., parked, doors closed).
3
Scan for error codes using an OBD-II scanner to identify any related issues.
4
Inspect the remote start system fuse for any signs of damage or failure.
5
Verify that the vehicle's security system is functioning properly and not preventing remote start.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Flathead screwdriver
•Fuse pullers

Parts Required

•Key fob battery
•Replacement fuse

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the key fob battery level using a multimeter or by replacing it with a new battery.
2
Ensure the vehicle is in the correct mode for remote start (e.g., parked, doors closed).
3
Scan for error codes using an OBD-II scanner to identify any related issues.
4
Inspect the remote start system fuse for any signs of damage or failure.
5
Verify that the vehicle's security system is functioning properly and not preventing remote start.

Solution

1. Preparation

Gather tools: OBD-II scanner, multimeter, flathead screwdriver, replacement key fob battery (if needed).
Ensure the vehicle is parked safely and the ignition is off.

2. Replace Key Fob Battery

Sub-steps:
1. Open the key fob using a flathead screwdriver to gently pry it apart.
2. Remove the old battery and insert a new battery, ensuring the correct polarity (+/-).
3. Snap the key fob back together securely.

3. Inspect and Replace Fuse

Sub-steps:
1. Locate the fuse box (usually under the dashboard or in the engine compartment).
2. Identify the fuse related to the remote start function (refer to the owner's manual).
3. Remove the fuse using fuse pullers or pliers and inspect for damage.
4. If damaged, replace it with a new fuse of the same amperage.

4. Reprogram Key Fob (if necessary)

Sub-steps:
1. Insert the key into the ignition and turn it to the "On" position without starting the engine.
2. Press and hold the lock button on the key fob for approximately 5 seconds.
3. Turn the ignition off and test the remote start function again.

5. Test Remote Start System

Sub-steps:
1. Ensure all doors are closed and the vehicle is in park.
2. Press the remote start button on the key fob and observe if the engine starts.
3. If it works, verify that the system operates correctly multiple times.