how to fix the AC not blowing cold air in my Volkswagen Golf Eighth Generation (2020-present)

Volkswagen Golf Eighth Generation (2020-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

583 words

Problem Statement

Learn how to diagnose and fix AC not blowing cold air in Volkswagen Golf (2020-present). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Always recover refrigerant before servicing AC components.
•Wear safety glasses and gloves when working with refrigerants and AC components.

Symptoms

•AC blows warm air instead of cold
•Unusual noises from the AC compressor
•AC system cycles on and off frequently
•Fogging or condensation on the interior windows
•Odor coming from the AC vents

Diagnostic Steps

1
Check the refrigerant level using a manifold gauge set.
2
Inspect the AC compressor for signs of damage or malfunction.
3
Verify the operation of the AC clutch by observing its engagement.
4
Examine the cabin air filter for blockages or restriction.
5
Inspect AC lines for leaks or damage.
6
Use an OBD-II scanner to check for related error codes.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Manifold gauge set
•Socket set
•Screwdrivers
•UV dye and UV light (optional)

Parts Required

•Refrigerant (R-134a or R-1234yf)
•AC compressor (if replacement is needed)
•Cabin air filter

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the refrigerant level using a manifold gauge set.
2
Inspect the AC compressor for signs of damage or malfunction.
3
Verify the operation of the AC clutch by observing its engagement.
4
Examine the cabin air filter for blockages or restriction.
5
Inspect AC lines for leaks or damage.
6
Use an OBD-II scanner to check for related error codes.

Solution

1. Preparation

Gather tools and parts needed.
Ensure the vehicle is parked on a level surface, and the engine is off.
Disconnect the battery to avoid electrical issues.

2. Check and Recharge Refrigerant

Tools Required: Manifold gauge set, refrigerant (R-134a or R-1234yf as specified).
Sub-steps:
1. Connect the manifold gauges to the low and high-pressure ports of the AC system.
2. Check the pressure readings against manufacturer specifications.
3. If low, add the appropriate refrigerant until the correct pressure is reached, following safety procedures.

3. Inspect and Replace AC Components

Tools Required: Socket set, screwdrivers, AC compressor oil (if necessary).
Sub-steps:
1. If the compressor is not engaging, check the electrical connections and fuses.
2. If damaged, remove the AC compressor by disconnecting the refrigerant lines (ensure refrigerant is properly recovered).
3. Replace the compressor with a new or remanufactured unit and refill with the correct amount of compressor oil.
4. Reconnect the refrigerant lines securely.

4. Clean or Replace Cabin Air Filter

Tools Required: Screwdriver (if applicable).
Sub-steps:
1. Locate the cabin air filter compartment (usually behind the glove box).
2. Remove the filter cover and take out the old filter.
3. Clean the compartment and install a new filter, ensuring it is oriented correctly.

5. Leak Testing and Final Checks

Tools Required: UV dye and UV light (optional).
Sub-steps:
1. If leaks were suspected, inject UV dye into the AC system and run the AC for 15 minutes.
2. Use a UV light to inspect for dye leaks in the system.
3. Repair any leaks found before recharging the system.