my Toyota Highlander XU70 (2020-Present) makes a knocking noise when accelerating, what's wrong?

Toyota Highlander XU70 (2020-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

517 words

Problem Statement

Learn how to diagnose and fix knocking noise during acceleration in Toyota Highlander XU70. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Ensure the vehicle is securely lifted and supported before working underneath.

Symptoms

•Knocking noise heard during acceleration
•Sound intensifies with increased speed
•Possible vibrations felt in the cabin
•Unusual sounds may also occur when turning
•Potential loss of power during acceleration

Diagnostic Steps

1
Inspect the engine and transmission mounts for signs of wear or damage.
2
Check for loose or damaged exhaust components that may cause noise during acceleration.
3
Examine the driveshaft and CV joints for any signs of wear or damage.
4
Inspect suspension components (e.g., control arms, bushings) for any signs of wear or damage.
5
Scan for any stored trouble codes using an OBD-II scanner.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Jack
•Jack stands
•Pry bar
•Wrench set
•Exhaust hanger removal tool
•Socket set
•Torque wrench

Parts Required

•Engine mounts (if damaged)
•Transmission mounts (if damaged)
•Exhaust hangers (if damaged)
•Driveshaft (if damaged)
•CV joints (if damaged)
•Suspension components (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the engine and transmission mounts for signs of wear or damage.
2
Check for loose or damaged exhaust components that may cause noise during acceleration.
3
Examine the driveshaft and CV joints for any signs of wear or damage.
4
Inspect suspension components (e.g., control arms, bushings) for any signs of wear or damage.
5
Scan for any stored trouble codes using an OBD-II scanner.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is on a flat surface and parked safely.
Disconnect the battery to ensure safety while working on electrical components.

2. Inspect Engine and Transmission Mounts

Sub-steps:
1. Raise the vehicle using a jack and secure it with jack stands.
2. Visually inspect the engine and transmission mounts for cracks or excessive wear.
3. Use a pry bar to check for movement in the mounts; they should not allow excessive play.
Tools Required: Jack, jack stands, pry bar.

3. Check Exhaust Components

Sub-steps:
1. Perform a visual inspection of the exhaust system for loose or damaged hangers.
2. Secure any loose components and replace damaged parts as necessary.
Tools Required: Wrench set, exhaust hanger removal tool.

4. Inspect Drivetrain Components

Sub-steps:
1. Examine the driveshaft for any signs of damage and ensure it is properly secured.
2. Inspect CV joints for torn boots or excess play.
3. Replace any damaged components as necessary.
Tools Required: Socket set, torque wrench.

5. Examine Suspension Components

Sub-steps:
1. Inspect control arms, bushings, and sway bar links for wear or damage.
2. Replace any worn or damaged suspension parts.
Tools Required: Socket set, torque wrench.