What should I do if the tire pressure monitoring system warning light is on?

Toyota Highlander Fourth Generation (2020-present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

4 min read

676 words

Problem Statement

Learn how to diagnose and fix the TPMS warning light issue on your Toyota Highlander (2020-present) with step-by-step instructions.

Affected Component

Tire Pressure Monitoring System (TPMS)

Estimated Time

1-2 hours

Symptoms

•The TPMS warning light is illuminated on the dashboard.
•Low tire pressure in one or more tires.
•Uneven tire wear.
•Vehicle handling issues (e.g., pulling to one side).

Diagnostic Steps

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Tire pressure gauge
•Air compressor (if needed)
•Tire repair kit (if a tire leak is suspected)
•OBD-II scanner (optional, for further diagnosis)
•Torque wrench (for tightening valve stems if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

Tire Pressure Monitoring System (TPMS) Warning Light On - Toyota Highlander (2020-present)

Tools Required:

Tire pressure gauge.
Air compressor (if needed).
Tire repair kit (if a tire leak is suspected).
OBD-II scanner (optional, for further diagnosis).
Torque wrench (for tightening valve stems if needed).

Step-by-Step Diagnostic and Repair Instructions:

Step 1: Check the Tire Pressure

Park the Vehicle Safely
- Ensure the vehicle is parked on a flat surface and the engine is off.
Inspect Each Tire
- Use the tire pressure gauge to check the pressure of each tire, including the spare (if applicable).
- Refer to the sticker located on the driver’s side door jamb or the owner’s manual for the correct tire pressure specifications.
Adjust Tire Pressure
- If any tire is below the recommended pressure, use an air compressor to inflate it to the specified PSI.
- If a tire is overinflated, release some air until it reaches the correct level.

Step 2: Inspect for Damage or Leaks

Visual Inspection
- Look for any visible signs of damage, such as cuts, punctures, or sidewall bulges on all tires.
- Check the valve stems for cracks or leaks.
Leak Test
- If a tire appears to be losing pressure quickly, consider applying a mixture of soap and water to the tire and valve stem.
- Look for bubbles, which indicate a leak.

Step 3: Reset the TPMS Light

Reset Process
- After correcting the tire pressure, you may need to reset the TPMS light.
- Turn the ignition key to the "ON" position without starting the engine.
- Locate the TPMS reset button (usually found under the dashboard near the steering column).
- Press and hold the reset button until the TPMS light blinks three times, then release it.
Drive the Vehicle
- Drive the vehicle for about 10 minutes at speeds above 15 mph to allow the system to recalibrate.

Step 4: Check for Fault Codes (if light still on)

Connect OBD-II Scanner
- If the TPMS light remains on after checking and adjusting tire pressures, connect an OBD-II scanner to the vehicle’s port (typically under the dashboard).
Read Fault Codes
- Check for any TPMS-related error codes. Common codes may indicate a faulty sensor or a problem with the TPMS control module.
Interpret Codes
- Refer to the scanner’s manual or an online database to interpret the codes and determine further actions.

Step 5: Replace Faulty TPMS Sensor (if needed)

Identify the Faulty Sensor
- If the OBD-II scanner indicates a specific tire sensor is faulty, that sensor will need replacement.
Remove the Tire
- Remove the wheel from the vehicle. This may require a lug wrench and a jack.
- Ensure the vehicle is securely supported before working on the wheels.
Install New TPMS Sensor
- Remove the old sensor from the rim.
- Install the new TPMS sensor, ensuring it is properly seated and the valve is securely tightened with a torque wrench as per the manufacturer's specifications.
Reinstall the Tire
- Reinstall the tire on the wheel and secure it with lug nuts.
- Lower the vehicle and ensure all tires are properly inflated.

Step 6: Final Check

Recheck Tire Pressures
- After all repairs, recheck the tire pressures once more.
Final Reset
- Perform the TPMS reset procedure again if necessary.
Test Drive
- Conduct a test drive to ensure the TPMS light stays off and that the vehicle handles correctly.

Conclusion

If the TPMS warning light remains illuminated after following these steps, it may require further diagnosis by a qualified technician. There could be an issue with the TPMS control module or other related components.