why is my Toyota Corolla E170 (2013-2019) jerking when shifting gears

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

514 words

Problem Statement

Learn how to diagnose and fix transmission jerking issues in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the transmission fluid fill plug.

Symptoms

•Jerking sensation during gear changes
•Delay in acceleration response
•Engine RPM fluctuating unexpectedly
•Possible transmission warning light illuminated
•Rough idle when at a stop
•Unusual noises during shifting (e.g., clunking or grinding)

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for transmission-related fault codes.
2
Inspect transmission fluid levels and condition (color and smell).
3
Check for any visible leaks around the transmission and fluid lines.
4
Examine the condition of the engine and transmission mounts for wear or damage.
5
Test the throttle position sensor (TPS) and mass airflow sensor (MAF) for proper function.
6
Perform a road test to observe shifting behavior under different driving conditions.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Multimeter
•Drain pan
•Funnel

Parts Required

•Transmission fluid (Toyota ATF WS)
•Transmission filter (if applicable)
•Throttle position sensor (if needed)
•Engine/transmission mounts (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for transmission-related fault codes.
2
Inspect transmission fluid levels and condition (color and smell).
3
Check for any visible leaks around the transmission and fluid lines.
4
Examine the condition of the engine and transmission mounts for wear or damage.
5
Test the throttle position sensor (TPS) and mass airflow sensor (MAF) for proper function.
6
Perform a road test to observe shifting behavior under different driving conditions.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is on a level surface and securely supported.
Disconnect the battery to prevent electrical shorts.

2. Check and Replace Transmission Fluid

Inspect Fluid Condition: Remove the transmission dipstick and check fluid color and smell. If it is dark or burnt, it needs replacement.
Replace Fluid:
1. Drain the old transmission fluid using a drain pan.
2. Replace the transmission filter (if applicable).
3. Refill with the recommended transmission fluid (Toyota ATF WS) using a funnel through the dipstick tube.
4. Ensure the fluid level is at the correct mark on the dipstick.

3. Inspect and Replace Component Parts

Inspect Mounts:
1. Visually check engine and transmission mounts for cracks or excessive wear.
2. Replace any damaged mounts with new ones.
Throttle Position Sensor (TPS):
1. Disconnect the electrical connector from the TPS.
2. Use a multimeter to test the resistance values according to the service manual specifications.
3. Replace the TPS if it fails the test.

4. Transmission Control Module (TCM) Update

Connect a scan tool to check for TCM updates.
If an update is available, perform the update following the manufacturer's instructions.