why is my Toyota Corolla E170 (2013-2019) brake pedal going to the floor

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

critical

Severity

3 min read

531 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the brake pedal going to the floor in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms and solutions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always allow the engine to cool before working on the braking system.
•Ensure the vehicle is securely supported before removing wheels.

Symptoms

•Brake pedal feels soft or spongy
•Brake warning light illuminated on the dashboard
•Reduced braking effectiveness or longer stopping distances
•Fluid leakage under the vehicle
•Unusual noises from the brake system when pressed

Diagnostic Steps

1
Inspect brake fluid level in the master cylinder reservoir.
2
Check for any visible leaks in brake lines or at the wheel cylinders/calipers.
3
Monitor the condition of the brake fluid for contamination or air bubbles.
4
Inspect brake pads and rotors for wear or damage.
5
Test the brake booster operation for proper function.
6
Scan the vehicle's computer for any brake-related error codes.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Wrench set
•Brake fluid tester
•Brake bleeder kit
•Torque wrench

Parts Required

•Brake fluid (DOT 3 or DOT 4)
•Brake pads (if worn)
•Brake rotors (if damaged)
•Brake line (if leaking)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake fluid level in the master cylinder reservoir.
2
Check for any visible leaks in brake lines or at the wheel cylinders/calipers.
3
Monitor the condition of the brake fluid for contamination or air bubbles.
4
Inspect brake pads and rotors for wear or damage.
5
Test the brake booster operation for proper function.
6
Scan the vehicle's computer for any brake-related error codes.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the ignition is off.
Wear safety gloves and goggles.

2. Check and Refill Brake Fluid

Open the hood and locate the brake master cylinder.
Remove the cap and check the brake fluid level.
If low, add the appropriate type of brake fluid (DOT 3 or DOT 4) until it reaches the full mark.

3. Inspect and Repair Brake Lines

Visually inspect all brake lines for cracks or signs of corrosion.
If any leaks are found, replace the damaged section of the brake line using a line wrench.
Bleed the brake system to remove air after any repairs.

4. Inspect Brake Components

Remove the wheel to access the brake calipers and pads.
Check the brake pads for wear; replace if the friction material is less than 3mm.
Inspect the rotors for scoring or warping; replace if necessary.
Reassemble the brake components ensuring all bolts are torqued to specifications.

5. Test Brake Booster

With the engine running, press the brake pedal several times. It should feel firm.
If the pedal sinks to the floor, the brake booster may be faulty and should be tested and replaced if necessary.