why does my Toyota Corolla E170 (2013-2019) transmission slip when accelerating

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

534 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission slipping in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Allow the engine to cool before working on the transmission.
•Use safety glasses and gloves to avoid injury from sharp edges.
•Disconnect the battery before working on electrical systems.

Symptoms

•Transmission slips during acceleration
•Delayed engagement when shifting from park to drive
•Engine revs higher than normal without corresponding vehicle acceleration
•Warning light illuminated on the dashboard
•Unusual noises from the transmission area
•Poor fuel economy

Diagnostic Steps

1
Check the transmission fluid level and condition using the dipstick.
2
Inspect for any transmission fluid leaks under the vehicle.
3
Scan the vehicle's onboard computer for any error codes using an OBD-II scanner.
4
Examine the transmission control module (TCM) for proper operation.
5
Test the transmission fluid for proper pressure using a gauge.
6
Inspect the transmission filter for clogs or restrictions.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Transmission funnel
•10mm socket
•Drain pan
•Socket set
•Torque wrench
•OBD-II scanner

Parts Required

•Transmission fluid (Toyota ATF WS)
•Transmission filter
•Transmission pan gasket

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the transmission fluid level and condition using the dipstick.
2
Inspect for any transmission fluid leaks under the vehicle.
3
Scan the vehicle's onboard computer for any error codes using an OBD-II scanner.
4
Examine the transmission control module (TCM) for proper operation.
5
Test the transmission fluid for proper pressure using a gauge.
6
Inspect the transmission filter for clogs or restrictions.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is cool.
Disconnect the negative battery terminal to prevent electrical issues.

2. Check and Replace Transmission Fluid

Sub-steps:
1. Remove the transmission dipstick and wipe it clean.
2. Reinsert and remove the dipstick to check the fluid level; top off if low with the recommended fluid type (Toyota ATF WS).
3. If the fluid is dark or burnt, proceed to drain and replace the fluid.
Tools Required: Transmission funnel, 10mm socket, drain pan.
Safety Warnings: Allow the engine to cool before working on the transmission.

3. Inspect and Replace Transmission Filter

Sub-steps:
1. Remove the transmission pan using a socket to access the filter.
2. Inspect the old filter for clogs or debris.
3. Replace with a new transmission filter and gasket.
4. Reinstall the transmission pan, ensuring to torque the bolts to manufacturer specifications (typically 8-10 ft-lbs).
Tools Required: Socket set, torque wrench, new transmission filter and gasket.
Safety Warnings: Use safety glasses and gloves to avoid injury from sharp edges.

4. Test Transmission Control Module (TCM)

Sub-steps:
1. Reconnect the battery terminal.
2. Use an OBD-II scanner to clear any transmission-related error codes.
3. Conduct a test drive to monitor the transmission's performance.
Tools Required: OBD-II scanner.
Safety Warnings: Make sure to adhere to traffic laws and safety regulations during the test drive.