why does my Toyota Corolla E170 (2013-2019) transmission jerk when shifting

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

576 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission jerking issues in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the transmission pan.

Symptoms

•Jerking sensation during gear shifts
•Delayed engagement when shifting from park to drive
•Unusual noises during shifting (clunking or grinding)
•Engine RPM fluctuations during acceleration
•Check engine light may be illuminated
•Poor fuel economy

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for transmission-related codes.
2
Inspect transmission fluid level and condition, looking for discoloration or burnt smell.
3
Check the transmission fluid for leaks around the transmission pan and seals.
4
Inspect the transmission linkage and mounts for any signs of wear or damage.
5
Test the transmission solenoids with a multimeter to ensure they are functioning correctly.
6
Check the condition of the engine and transmission mounts for excessive play.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Multimeter
•Fluid pump
•Torque wrench

Parts Required

•Transmission filter
•Transmission fluid (manufacturer-approved type)
•Transmission solenoids (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for transmission-related codes.
2
Inspect transmission fluid level and condition, looking for discoloration or burnt smell.
3
Check the transmission fluid for leaks around the transmission pan and seals.
4
Inspect the transmission linkage and mounts for any signs of wear or damage.
5
Test the transmission solenoids with a multimeter to ensure they are functioning correctly.
6
Check the condition of the engine and transmission mounts for excessive play.

Solution

1. Preparation

Tools Required: OBD-II scanner, socket set, multimeter, fluid pump, torque wrench.
Ensure the vehicle is on a level surface and secure with jack stands.
Disconnect the battery to prevent electrical shorts.

2. Fluid Change

Raise Vehicle:
- Use a jack to lift the vehicle and secure with jack stands.
Drain Old Fluid:
- Locate the transmission fluid drain plug and remove it using a socket set.
- Allow the old fluid to completely drain into a suitable container.
Replace Transmission Filter:
- Remove the transmission pan using a socket set.
- Take out the old filter and replace it with a new one, ensuring the new filter is seated properly.
- Clean the pan and check for metal shavings or debris, indicating internal wear.
Reinstall Pan:
- Replace the pan and tighten the bolts to the manufacturer’s specified torque settings.
Add New Fluid:
- Use a fluid pump to add new transmission fluid through the dipstick tube, using the manufacturer-recommended fluid type.
- Check the fluid level with the engine running to ensure it is at the proper level.

3. Solenoid Replacement (if needed)

Access Transmission Solenoids:
- If solenoids are found faulty, remove the transmission pan again and locate the solenoids.
Remove and Replace Solenoids:
- Disconnect the electrical connectors and unscrew the solenoids from their mounting locations.
- Install new solenoids and reconnect the electrical connectors.
Reassemble Components:
- Reinstall the transmission pan and ensure all bolts are tightened to the specified torque.