why does my Toyota Corolla E170 (2013-2019) transmission jerk when changing gears

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

498 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission jerking in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before working on the transmission.

Symptoms

•Jerking or hard shifting during gear change
•Delayed engagement when shifting from park to drive or reverse
•Unusual noises, such as grinding or clunking, during gear changes
•Check engine light illuminated
•Poor acceleration or loss of power during shifts

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related fault codes.
2
Check the transmission fluid level and condition; look for discoloration or burnt smell.
3
Inspect the transmission fluid filter for clogs or contamination.
4
Examine the transmission mounts for wear or damage.
5
Test the throttle position sensor (TPS) for proper function using a multimeter.
6
Check for vacuum leaks in the intake system that could affect transmission performance.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Transmission funnel
•Drain pan
•Socket set
•Torque wrench
•Multimeter
•Jack and jack stands

Parts Required

•Transmission fluid (correct type as per specifications)
•Transmission filter (if necessary)
•Transmission mounts (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related fault codes.
2
Check the transmission fluid level and condition; look for discoloration or burnt smell.
3
Inspect the transmission fluid filter for clogs or contamination.
4
Examine the transmission mounts for wear or damage.
5
Test the throttle position sensor (TPS) for proper function using a multimeter.
6
Check for vacuum leaks in the intake system that could affect transmission performance.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is cool.
Disconnect the negative battery terminal to avoid electrical shorts.

2. Check and Replace Transmission Fluid

Tools Required: Transmission funnel, drain pan, socket set, torque wrench
Remove the transmission pan bolts using a socket set and drain the fluid into a pan.
Inspect the pan for metal shavings or debris.
Replace the transmission filter if applicable.
Refill the transmission with the correct type of fluid (consult owner’s manual for specifications).
Torque the pan bolts to the manufacturer's specifications (usually around 8-10 ft-lbs).

3. Inspect and Replace Transmission Mounts (if necessary)

Tools Required: Jack and jack stands, socket set
Place the jack under the transmission and slightly lift it to relieve pressure from the mounts.
Remove the bolts securing the transmission mounts using a socket set.
Replace with new mounts and torque to the manufacturer’s specifications.
Lower the transmission back into place and recheck all connections.