why does my Toyota Corolla E170 (2013-2019) shake when I accelerate

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

507 words

Problem Statement

Discover the causes and solutions for shaking during acceleration in the 2013-2019 Toyota Corolla E170. Step-by-step diagnostic and repair guide.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical systems.
•Allow the vehicle to cool down before inspecting engine components.

Symptoms

•Vibration felt in the steering wheel or seat during acceleration
•Increased noise from the drivetrain or engine compartment
•Shaking that intensifies with higher speeds or during hard acceleration
•Possible steering wheel shake or pull to one side
•Unusual tire wear patterns

Diagnostic Steps

1
Inspect tire condition and pressure; look for imbalances or damage.
2
Check wheel alignment and balance; ensure all wheels are properly aligned.
3
Examine drivetrain components including drive shafts and axles for wear or damage.
4
Inspect engine and transmission mounts for signs of deterioration or failure.
5
Scan for error codes using an OBD-II scanner to check for underlying engine issues.
6
Test drive the vehicle to replicate and assess the shaking condition.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Jack and jack stands
•Tire pressure gauge

Parts Required

•New tires (if damaged)
•Engine and transmission mounts (if worn)
•CV joints or drive shafts (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect tire condition and pressure; look for imbalances or damage.
2
Check wheel alignment and balance; ensure all wheels are properly aligned.
3
Examine drivetrain components including drive shafts and axles for wear or damage.
4
Inspect engine and transmission mounts for signs of deterioration or failure.
5
Scan for error codes using an OBD-II scanner to check for underlying engine issues.
6
Test drive the vehicle to replicate and assess the shaking condition.

Solution

1. Preparation

Gather tools and parts required for the repair.
Ensure the vehicle is parked on a flat surface and securely lift it using a jack and jack stands.
Disconnect the battery if working on electrical components.

2. Tire Inspection and Replacement

Sub-steps:
1. Remove the wheel using a socket set.
2. Inspect the tires for uneven wear, bulges, or damage.
3. Check tire pressure and inflate to the manufacturer's recommended PSI.
4. If tires are damaged, replace them with new tires.
5. Reinstall the wheel and torque to the manufacturer’s specifications (usually 80-100 ft-lbs).

3. Wheel Alignment and Balancing

Sub-steps:
1. Take the vehicle to a professional alignment shop.
2. Have the wheels balanced; ask for a printout of the alignment specifications.
3. Adjust alignment as necessary to manufacturer specifications.

4. Drivetrain Inspection

Sub-steps:
1. Inspect drive shafts for any signs of wear or damage.
2. Look for any loose or damaged CV joints.
3. Replace any damaged components as necessary.

5. Engine and Transmission Mounts

Sub-steps:
1. Visually inspect engine and transmission mounts for cracks or separation.
2. If damaged, remove the old mounts using a socket set and replace with new mounts.
3. Torque new mounts to the manufacturer's specifications.