why does my Toyota Corolla E170 (2013-2019) make noise when I hit the brakes

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

500 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix brake noise issues in the 2013-2019 Toyota Corolla E170. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on the braking system.
•Allow the brakes to cool before inspection or repair to prevent burns.

Symptoms

•Squeaking or squealing noise when brakes are applied
•Grinding noise when braking
•Pulsation felt through the brake pedal
•Reduced braking effectiveness
•Brake warning light illuminated on the dashboard

Diagnostic Steps

1
Inspect brake pads visually for wear and damage.
2
Check brake rotors for scoring or warping.
3
Examine brake calipers for proper operation and any sticking.
4
Inspect brake lines for leaks or damage.
5
Test brake fluid level and condition.
6
Listen for noises while applying brakes at low speeds to identify the source.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Lug wrench
•Socket set
•Brake cleaner
•Torque wrench
•C-clamp
•Safety glasses
•Gloves

Parts Required

•Brake pads
•Brake rotors (if necessary)
•Brake grease

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake pads visually for wear and damage.
2
Check brake rotors for scoring or warping.
3
Examine brake calipers for proper operation and any sticking.
4
Inspect brake lines for leaks or damage.
5
Test brake fluid level and condition.
6
Listen for noises while applying brakes at low speeds to identify the source.

Solution

1. Preparation

Tools Required:
- Jack and jack stands
- Lug wrench
- Socket set
- Brake cleaner
- Torque wrench
- C-clamp
- Safety glasses and gloves
Ensure vehicle is parked on a level surface and engage the parking brake.

2. Raise the Vehicle

Use a jack to lift the front or rear of the vehicle, depending on which brakes are making noise.
Secure the vehicle with jack stands.

3. Remove Wheel

Use a lug wrench to remove the lug nuts.
Take off the wheel to access the brake components.

4. Inspect and Replace Brake Pads

Inspect:
- Remove the caliper by unscrewing the caliper bolts.
- Check brake pads for wear; replace if they are less than 3mm thick.
Replace:
- If necessary, remove old brake pads and install new ones.
- Apply brake grease to the backing of new pads to reduce noise.

5. Inspect and Resurface/Replace Rotors

Check the rotors for grooves or uneven surfaces.
If rotors are damaged, either resurface them or replace with new rotors.
Ensure proper torque specs when attaching rotors (typically between 70-100 ft-lbs, check specific guidelines).

6. Reassemble and Lower Vehicle

Reattach the brake caliper over the new pads and secure it with bolts.
Reinstall the wheel and hand-tighten the lug nuts.
Lower the vehicle and then use a torque wrench to tighten the lug nuts to the manufacturer’s specifications.