why does my Toyota Corolla E170 (2013-2019) make a popping sound when turning

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

518 words

Problem Statement

Learn how to diagnose and fix the popping sound when turning in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always ensure the vehicle is securely lifted and supported before working underneath.
•Disconnect the battery before starting work on electrical components.

Symptoms

•Popping or clicking noise during turns
•Noise occurs primarily when steering left or right
•Possible vibrations felt through the steering wheel
•Uneven tire wear
•Difficulty steering or a loose feeling in the steering wheel

Diagnostic Steps

1
Inspect the front suspension components for wear or damage.
2
Check the CV joints and axles for any signs of wear or separation.
3
Examine the steering linkage and tie rods for play or damage.
4
Look for any loose or damaged heat shields or exhaust components that may be causing noise.
5
Test drive the vehicle to replicate the popping sound and identify under what conditions it occurs.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Pry bar
•Jack and jack stands

Parts Required

•CV joint (if necessary)
•Suspension bushings or components (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front suspension components for wear or damage.
2
Check the CV joints and axles for any signs of wear or separation.
3
Examine the steering linkage and tie rods for play or damage.
4
Look for any loose or damaged heat shields or exhaust components that may be causing noise.
5
Test drive the vehicle to replicate the popping sound and identify under what conditions it occurs.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety during repairs.

2. Inspect and Replace CV Joints

Tools Required: Socket set, torque wrench, pry bar, CV joint boot clamps.
Instructions:
1. Lift the Vehicle: Use a jack to lift the front of the vehicle and secure it with jack stands.
2. Remove the Wheel: Take off the front wheel to access the CV joint.
3. Inspect CV Joint: Visually inspect the CV joint for torn boots or grease leakage.
4. Remove CV Axle:
  - Use a socket set to remove the axle nut.
  - Disconnect the lower ball joint if necessary to free the axle.
5. Replace CV Joint: If damaged, install a new CV joint. Ensure it's properly seated and secure it with the new clamps.
6. Reassemble: Reattach the axle to the hub and tighten the axle nut to the manufacturer’s torque specifications (typically around 150 ft-lbs).

3. Inspect and Replace Suspension Components

Tools Required: Socket set, torque wrench, pry bar.
Instructions:
1. Check Suspension: Look for worn bushings, struts, or ball joints in the suspension.
2. Replace Damaged Components: If any parts are worn, replace them (e.g., control arms, strut mounts).
3. Reassemble: Reattach all components and secure them according to the manufacturer’s specifications.