why does my Toyota Corolla E170 (2013-2019) make a popping noise when turning

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

556 words

Problem Statement

Learn to diagnose and fix popping noise when turning in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical components.
•Allow the vehicle to cool before servicing the suspension or steering systems.

Symptoms

•Popping or clicking noise during turns
•Noise may be more pronounced when turning sharply
•Possible vibrations felt through the steering wheel
•Reduced steering responsiveness
•Unusual tire wear patterns
•Check engine light may illuminate if related to other components

Diagnostic Steps

1
Inspect the front suspension components for any visible damage or wear.
2
Check the CV joints for any signs of damage or excessive play.
3
Examine the wheel bearings for signs of wear or noise.
4
Test drive the vehicle to replicate the noise while observing steering and suspension behavior.
5
Check for any loose or damaged components in the steering linkage.
6
Inspect tire condition and alignment settings.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Socket set
•Torque wrench
•Flathead screwdriver
•Pry bar

Parts Required

•CV joint assembly (if applicable)
•Tie rod ends (if applicable)
•Control arm bushings (if applicable)
•Wheel bearings (if applicable)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front suspension components for any visible damage or wear.
2
Check the CV joints for any signs of damage or excessive play.
3
Examine the wheel bearings for signs of wear or noise.
4
Test drive the vehicle to replicate the noise while observing steering and suspension behavior.
5
Check for any loose or damaged components in the steering linkage.
6
Inspect tire condition and alignment settings.

Solution

1. Preparation

Ensure the vehicle is parked on a level surface and engage the parking brake.
Gather necessary tools and parts.
Wear safety glasses and gloves.

2. Inspect and Replace CV Joints

Tools Required: Jack, jack stands, socket set, torque wrench, flathead screwdriver, pry bar.
Lift the front of the vehicle using a jack and secure it with jack stands.
Remove the wheel to access the CV joint.
Inspect the CV boot for tears or leaks; if damaged, replace the entire CV joint assembly.
If replacing, remove the retaining clip and use a pry bar to detach the joint from the hub.
Install the new CV joint, ensuring it is properly seated and secured with a new retaining clip.
Reinstall the wheel and lower the vehicle.

3. Inspect and Replace Suspension Components

Tools Required: Socket set, torque wrench, pry bar.
Check the tie rod ends for wear; replace if there is excessive play.
Inspect the control arm bushings for cracks or deterioration; replace if necessary.
Tighten or replace any loose bolts or nuts according to manufacturer's torque specifications.

4. Check Wheel Bearings

Tools Required: Socket set, torque wrench.
While the wheel is removed, spin the hub and listen for grinding or roughness.
If the wheel bearing is noisy, remove the hub assembly and replace the bearing.
Reassemble and torque all bolts to specifications.