why does my Toyota Corolla E170 (2013-2019) make a popping noise when turning

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

510 words

Problem Statement

Learn how to diagnose and fix popping noise when turning in a 2013-2019 Toyota Corolla E170. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always secure the vehicle on jack stands before working underneath it.
•Disconnect the battery before working on electrical components.

Symptoms

•Popping or clicking noise during turns
•Noise occurs when steering at low speeds
•Vibration felt in the steering wheel
•Uneven tire wear
•Possible decrease in steering responsiveness

Diagnostic Steps

1
Inspect the front suspension components visually for visible wear or damage.
2
Check the CV joints and boot for any tears or excessive play.
3
Test the steering system for any looseness or abnormal movement.
4
Examine the wheel bearings for signs of wear or failure.
5
Check the tire condition and alignment for any abnormalities.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Socket set
•Pliers
•Wheel chocks

Parts Required

•CV joint assembly
•Suspension components (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front suspension components visually for visible wear or damage.
2
Check the CV joints and boot for any tears or excessive play.
3
Test the steering system for any looseness or abnormal movement.
4
Examine the wheel bearings for signs of wear or failure.
5
Check the tire condition and alignment for any abnormalities.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and engage the parking brake.
Disconnect the battery if working on electrical components.

2. Inspect and Replace CV Joints

Lift the Vehicle
- Use a jack to lift the front of the vehicle and secure it on jack stands.
- Tools required: Jack, jack stands, wheel chocks.
Remove the Wheel
- Remove the lug nuts using a socket wrench and take off the front wheel.
- Tools required: Socket set.
Inspect the CV Joint
- Check the CV joint for signs of wear, including cracks or tears in the boot.
- If damaged, proceed to replace the CV joint.
Remove the CV Joint
- Disconnect the axle from the wheel hub and remove the retaining clips.
- Gently pull out the CV joint from the transmission.
- Tools required: Pliers, socket set.
Install New CV Joint
- Insert the new CV joint into the transmission and secure it with retaining clips.
- Reattach the axle to the wheel hub.
- Torque specifications: Refer to the service manual for the specific torque values.

3. Inspect and Replace Suspension Components

Check Suspension Components
- Inspect struts, control arms, and bushings for any signs of wear or damage.
- Replace any damaged components.
Reassemble the Wheel
- Put the wheel back on and hand-tighten the lug nuts.
- Lower the vehicle and torque the lug nuts to the manufacturer’s specifications.
Test Drive
- Take the vehicle for a test drive to confirm that the popping noise has been resolved.