why does my Toyota Corolla E170 (2013-2019) make a hissing noise when starting

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

487 words

Problem Statement

Diagnose and fix the hissing noise during engine start in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostics, and solutions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before performing any maintenance on the intake system.

Symptoms

•Hissing noise during engine start
•Possible rough idle upon start
•Check engine light illuminated (if applicable)
•Decreased engine performance
•Increased fuel consumption

Diagnostic Steps

1
Inspect the intake system for any visible cracks or loose connections.
2
Check vacuum hoses for signs of wear or damage.
3
Use an OBD-II scanner to check for any stored error codes.
4
Listen for the hissing sound while applying slight pressure to different sections of the intake system.
5
Perform a smoke test to identify any vacuum leaks.
6
Inspect the throttle body for cleanliness and proper operation.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Throttle body cleaner
•Soft brush
•Clean cloth
•Smoke machine
•Socket set

Parts Required

•Replacement vacuum hoses (if necessary)
•Throttle body gasket (if removed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the intake system for any visible cracks or loose connections.
2
Check vacuum hoses for signs of wear or damage.
3
Use an OBD-II scanner to check for any stored error codes.
4
Listen for the hissing sound while applying slight pressure to different sections of the intake system.
5
Perform a smoke test to identify any vacuum leaks.
6
Inspect the throttle body for cleanliness and proper operation.

Solution

1. Preparation

Gather tools and parts.
Ensure the vehicle is parked on a level surface and the engine is cool.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Inspect and Replace Vacuum Hoses

Sub-steps:
1. Locate the vacuum hoses connected to the intake manifold.
2. Inspect each hose for cracks, splits, or loose fittings.
3. Replace any damaged hoses with new ones. Ensure they are secured tightly.

3. Clean the Throttle Body

Tools Required: Throttle body cleaner, soft brush, clean cloth.
Sub-steps:
1. Remove the air intake duct connected to the throttle body.
2. Spray throttle body cleaner onto the throttle plate and surrounding areas.
3. Use a soft brush to gently scrub any carbon deposits.
4. Wipe clean with a cloth and reassemble the intake duct.

4. Conduct a Smoke Test

Tools Required: Smoke machine.
Sub-steps:
1. Connect the smoke machine to the intake system.
2. Activate the machine and observe for any smoke escaping from hoses or connections.
3. Identify and repair any leaks found.

5. Reassemble and Test

Sub-steps:
1. Reconnect the battery terminal.
2. Start the engine to check for the hissing noise.
3. Allow the engine to idle and monitor for any abnormal sounds or warning lights.