why does my Toyota Corolla E170 (2013-2019) make a grinding noise when braking

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

508 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix grinding noise when braking in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on the braking system.
•Allow the vehicle to cool down before working on the brakes to avoid burns.

Symptoms

•Grinding noise when applying brakes
•Decreased braking performance
•Vibration in the brake pedal
•Brake warning light illuminated
•Increased stopping distance

Diagnostic Steps

1
Inspect the brake pads for wear and damage.
2
Check the brake rotors for scoring or warping.
3
Examine the brake calipers for proper operation and leaks.
4
Inspect brake fluid level and condition.
5
Look for debris or foreign objects lodged in the brake assembly.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Lug wrench
•Socket set
•Torque wrench
•Brake cleaner
•Replacement brake pads
•Optional: Brake rotors

Parts Required

•Brake pads
•Brake rotors

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is on a flat surface and the parking brake is engaged.
Wear safety gloves and goggles.

2. Remove Wheel

Loosen lug nuts slightly while the vehicle is on the ground.
Raise the vehicle using a jack and secure it with jack stands.
Remove the wheel completely.

3. Inspect and Replace Brake Pads

Remove the caliper bolts using a socket wrench.
Carefully slide the caliper off the rotor and support it (do not let it hang by the brake line).
Remove the old brake pads from the caliper bracket.
Inspect the old pads; if they are worn down to the metal, they need replacement.
Install new brake pads in the caliper bracket, ensuring they are seated properly.

4. Inspect and Resurface/Replace Rotors

Check the rotors for any grooves or scoring.
If the rotors are damaged, remove them by unscrewing the retaining screws (if applicable) and sliding them off the hub.
If they are in good condition, you may choose to resurface them instead of replacing.
Clean the rotor surface with brake cleaner to remove any debris or grease.

5. Reassemble Braking System

Reinstall the caliper over the new brake pads.
Tighten the caliper bolts to the manufacturer’s specified torque settings (typically around 20-25 ft-lbs).
Reinstall the wheel and hand-tighten the lug nuts.
Lower the vehicle and then fully tighten the lug nuts in a crisscross pattern.

Tools Required:

Jack and jack stands
Lug wrench
Socket set
Torque wrench
Brake cleaner
Replacement brake pads
Optional: Brake rotors (if needed)

Parts Required:

Brake pads (ensure correct fit for Toyota Corolla E170)
Brake rotors (if needed)

Estimated Repair Time: 2-4 hours

Safety Warnings:

Always disconnect the battery before working on the braking system.
Allow the vehicle to cool down before working on the brakes to avoid burns.