why does my Toyota Corolla E170 (2013-2019) make a clicking noise when driving

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

550 words

Problem Statement

Learn how to diagnose and fix the clicking noise in your 2013-2019 Toyota Corolla E170. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under a vehicle.
•Allow the engine to cool before performing any work on components that may be hot.

Symptoms

•Clicking noise that increases with vehicle speed
•Noise present during acceleration and deceleration
•Possible vibration felt in the steering wheel or floorboard
•Unusual wear on tires
•Potential for loss of steering control or alignment issues

Diagnostic Steps

1
Inspect the tires for uneven wear patterns and ensure they are properly inflated.
2
Examine the wheel bearings for play or damage by jacking the vehicle and checking for lateral movement.
3
Check CV joints for signs of wear or damage, including torn boots or grease leakage.
4
Look for loose or damaged components in the suspension and steering systems.
5
Test drive the vehicle to replicate the noise while listening for its source.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Lug wrench
•Tire pressure gauge
•Socket set
•Torque wrench
•Bearing puller

Parts Required

•New CV joint (if applicable)
•New wheel bearings (if applicable)
•Replacement tires (if applicable)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the tires for uneven wear patterns and ensure they are properly inflated.
2
Examine the wheel bearings for play or damage by jacking the vehicle and checking for lateral movement.
3
Check CV joints for signs of wear or damage, including torn boots or grease leakage.
4
Look for loose or damaged components in the suspension and steering systems.
5
Test drive the vehicle to replicate the noise while listening for its source.

Solution

1. Preparation

Gather tools and parts required for the repair.
Park the vehicle on a flat surface and engage the parking brake.
Disconnect the battery if performing electrical work.

2. Tire Inspection and Replacement

Sub-steps:
1. Remove the wheel cover or hubcap if applicable.
2. Loosen the lug nuts slightly while the vehicle is still on the ground.
3. Jack up the vehicle and secure it with jack stands.
4. Remove the lug nuts completely and take off the wheel.
5. Inspect the tire for uneven wear; replace if necessary.
Tools Required: Jack, jack stands, lug wrench, tire pressure gauge.

3. CV Joint Replacement

Sub-steps:
1. Locate the CV joint and inspect for torn boots or grease leakage.
2. If damaged, remove the axle nut and disconnect the lower control arm.
3. Slide the axle out of the transmission and remove the old CV joint.
4. Install the new CV joint by reversing the removal steps.
5. Reassemble the lower control arm and torque the axle nut to manufacturer specifications.
Tools Required: Socket set, torque wrench, pry bar.

4. Wheel Bearing Replacement (if needed)

Sub-steps:
1. Remove the wheel and brake caliper to access the hub.
2. Unbolt the wheel bearing assembly from the hub.
3. Press out the old bearing using a bearing puller.
4. Press in the new bearing carefully, ensuring it is seated properly.
5. Reattach the hub assembly and brake caliper, then reinstall the wheel.
Tools Required: Bearing puller, socket set, torque wrench.