why does my Toyota Corolla E170 (2013-2019) check engine light keep coming on

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

440 words

Problem Statement

Discover how to diagnose and fix the check engine light issue in a 2013-2019 Toyota Corolla E170. Step-by-step guide with symptoms and solutions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems
•Allow the engine to cool before performing any maintenance on it

Symptoms

•Check engine light illuminated
•Engine runs rough or has a poor idle
•Decreased fuel efficiency
•Unusual noises from the engine
•Emission test failure
•Engine stalling or hesitation during acceleration

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to retrieve diagnostic trouble codes (DTCs)
2
Inspect the gas cap for proper sealing and any signs of damage
3
Check the engine oil level and condition
4
Examine the air filter for dirt and debris
5
Inspect the spark plugs and ignition coils for wear or damage
6
Test the battery voltage and connections for corrosion or weakness

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Fuel pressure gauge
•Screwdrivers

Parts Required

•Spark plugs
•Air filter
•Fuel filter (if needed)
•Oxygen sensor (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to retrieve diagnostic trouble codes (DTCs)
2
Inspect the gas cap for proper sealing and any signs of damage
3
Check the engine oil level and condition
4
Examine the air filter for dirt and debris
5
Inspect the spark plugs and ignition coils for wear or damage
6
Test the battery voltage and connections for corrosion or weakness

Solution

1. Preparation

Gather tools and parts.
Ensure the vehicle is parked on a level surface and the engine is cool.
Disconnect the battery by removing the negative terminal.

2. Address Fault Codes

Sub-step 1: Refer to the OBD-II codes obtained during diagnostics.
Sub-step 2: Research specific fault code meanings and suggested repairs.
Sub-step 3: Replace any faulty components indicated by the codes (e.g., oxygen sensor, catalytic converter).

3. Inspect and Replace Spark Plugs

Sub-step 1: Remove the ignition coils using a socket set.
Sub-step 2: Extract the spark plugs and inspect for wear, carbon buildup, or damage.
Sub-step 3: Replace with new spark plugs, ensuring to torque to the manufacturer's specification.

4. Air Filter Maintenance

Sub-step 1: Open the air filter housing by unclipping or unscrewing it.
Sub-step 2: Remove the old air filter and inspect for dirt and clogs.
Sub-step 3: Install a new air filter and reassemble the housing.

5. Check Fuel System

Sub-step 1: Inspect the fuel lines for leaks and damage.
Sub-step 2: If necessary, replace the fuel filter.
Sub-step 3: Test fuel pressure with a fuel pressure gauge to ensure proper operation.

6. Final Assembly

Sub-step 1: Reconnect the battery terminal.
Sub-step 2: Start the engine and monitor for any irregularities.
Sub-step 3: Ensure all components are secure and free of leaks.

Tools Required:

OBD-II scanner
Socket set
Torque wrench
Fuel pressure gauge
Screwdrivers

Parts Required:

Spark plugs
Air filter
Fuel filter (if needed)
Oxygen sensor (if faulty)

Estimated Repair Time: 2-4 hours

Safety Warnings:

Disconnect the battery before working on electrical systems.
Allow the engine to cool before performing any maintenance on it.