what should I do if my Toyota Corolla E170 (2013-2019) transmission slips?

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

542 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission slipping in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostics, and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the transmission pan.

Symptoms

•Slipping or delayed engagement when shifting gears
•Unusual whining or grinding noises during operation
•Engine revs higher than normal without corresponding acceleration
•Warning lights illuminated on the dashboard
•Poor fuel economy
•Transmission fluid leaks under the vehicle

Diagnostic Steps

1
Check the transmission fluid level and condition using the dipstick.
2
Scan for error codes using an OBD-II scanner to identify any related transmission faults.
3
Inspect the transmission fluid for contamination, burning smell, or metal shavings.
4
Examine the transmission filter and pan for clogs or damage.
5
Test the shift solenoids and components for proper operation with a multimeter.
6
Verify the operation of the throttle position sensor (TPS) for correct readings.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Multimeter
•Funnel
•Drain pan

Parts Required

•Transmission fluid (Toyota ATF WS)
•Transmission filter
•Transmission pan gasket
•Shift solenoids (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the transmission fluid level and condition using the dipstick.
2
Scan for error codes using an OBD-II scanner to identify any related transmission faults.
3
Inspect the transmission fluid for contamination, burning smell, or metal shavings.
4
Examine the transmission filter and pan for clogs or damage.
5
Test the shift solenoids and components for proper operation with a multimeter.
6
Verify the operation of the throttle position sensor (TPS) for correct readings.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure vehicle is parked on a level surface, and the engine is off.
Disconnect the negative battery terminal.

2. Check and Change Transmission Fluid

Tools Required: Socket set, funnel, drain pan.
Remove the transmission fluid dipstick to check fluid condition.
If fluid is low or burnt, proceed to change it.
1. Place a drain pan underneath the transmission pan.
2. Remove the transmission pan bolts with the socket set.
3. Carefully lower the pan and allow fluid to drain completely.
4. Replace the transmission filter, ensuring the new filter is seated properly.
5. Clean the transmission pan and replace the gasket with a new one.
6. Reinstall the transmission pan and torque bolts to manufacturer specifications.

3. Replace or Repair Shift Solenoids

Tools Required: Socket set, multimeter.
If solenoids are faulty:
1. Locate the transmission control module (TCM) and the solenoids.
2. Disconnect the electrical connectors from the solenoids.
3. Remove the solenoid assembly from the transmission.
4. Install the new solenoid assembly and secure it in place.
5. Reconnect electrical connectors.

4. Test Drive and Monitor

Reconnect the negative battery terminal.
Fill the transmission with the appropriate fluid type (Toyota ATF WS).
Start the engine and shift through all gears while stationary.
Test drive the vehicle to ensure proper operation and monitor for slipping.