what does it mean if the oil pressure light is on in Toyota Corolla E170 (2013-2019)

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

4 min read

614 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the oil pressure light issue in a 2013-2019 Toyota Corolla E170. Step-by-step guide with symptoms and solutions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool before opening the oil filler cap or drain plug.

Symptoms

•Oil pressure warning light illuminated on the dashboard
•Engine noise due to insufficient lubrication
•Oil leaks observed under the vehicle
•Reduced engine performance or stalling
•Increased engine temperature

Diagnostic Steps

1
Check the engine oil level using the dipstick; ensure it is within the recommended range.
2
Inspect for any visible oil leaks under the vehicle or around the engine.
3
Scan the vehicle's OBD-II system for any error codes related to oil pressure or engine performance.
4
Test the oil pressure using a mechanical oil pressure gauge to verify the actual pressure.
5
Inspect the oil pressure sending unit for proper operation and any signs of damage.
6
Check the oil filter for proper installation and signs of blockage.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Mechanical oil pressure gauge
•Socket set
•Wrench set
•Oil filter wrench
•Oil catch pan

Parts Required

•Oil pressure sending unit
•Engine oil (0W-20)
•Oil filter

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the engine oil level using the dipstick; ensure it is within the recommended range.
2
Inspect for any visible oil leaks under the vehicle or around the engine.
3
Scan the vehicle's OBD-II system for any error codes related to oil pressure or engine performance.
4
Test the oil pressure using a mechanical oil pressure gauge to verify the actual pressure.
5
Inspect the oil pressure sending unit for proper operation and any signs of damage.
6
Check the oil filter for proper installation and signs of blockage.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is turned off.
Disconnect the battery to ensure safety while working on electrical components.

2. Check Oil Level

Remove the dipstick, wipe it clean, and insert it back into the tube.
Pull the dipstick out again and check the oil level.
If low, add the recommended oil type (typically 0W-20 for the Corolla) until the correct level is reached.

3. Replace Oil Pressure Sending Unit

Tools Required: Socket set, wrench set, oil filter wrench, oil catch pan.
Locate the oil pressure sending unit, usually found near the oil filter.
Disconnect the electrical connector from the sending unit.
Use a socket to remove the sending unit and replace it with a new one, ensuring it is tightened to manufacturer specifications (typically around 15-20 ft-lbs).
Reconnect the electrical connector.

4. Change Engine Oil and Filter

Tools Required: Oil filter wrench, socket set.
Place an oil catch pan under the oil pan.
Remove the oil drain plug using a socket and allow the old oil to drain completely.
Replace the drain plug and tighten it to the specified torque (approximately 30 ft-lbs).
Use an oil filter wrench to remove the old oil filter.
Apply a thin layer of new oil to the rubber gasket of the new oil filter, then install it.
Fill the engine with the recommended oil type through the oil filler cap.

5. Reconnect Battery and Test

Reconnect the battery terminals.
Start the engine and allow it to idle for a few minutes.
Monitor the oil pressure light; it should turn off if the issue is resolved.