what causes my Toyota Corolla E170 (2013-2019) to jerk when shifting?

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

554 words

Problem Statement

Learn how to diagnose and fix transmission jerking in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before checking or changing transmission fluid.

Symptoms

•Jerking or lurching sensation when shifting gears
•Delayed engagement or response when accelerating
•Unusual noises during gear changes (e.g., clunking or grinding)
•Fluctuating RPMs during shifting
•Check engine light illuminated (potentially)

Diagnostic Steps

1
Scan the vehicle's onboard diagnostics using an OBD-II scanner to check for any stored error codes.
2
Inspect the transmission fluid level and condition; check for signs of contamination or burning smell.
3
Examine the transmission mounts for any signs of wear or damage.
4
Test the throttle position sensor (TPS) and mass airflow sensor (MAF) for proper function.
5
Check for vacuum leaks in the intake system that could affect engine performance.
6
Inspect the shift linkage for proper alignment and operation.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Drain pan
•Multimeter
•Torque wrench

Parts Required

•Transmission fluid (Toyota ATF WS)
•Transmission filter (if applicable)
•Transmission mounts (if worn)
•Throttle position sensor (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's onboard diagnostics using an OBD-II scanner to check for any stored error codes.
2
Inspect the transmission fluid level and condition; check for signs of contamination or burning smell.
3
Examine the transmission mounts for any signs of wear or damage.
4
Test the throttle position sensor (TPS) and mass airflow sensor (MAF) for proper function.
5
Check for vacuum leaks in the intake system that could affect engine performance.
6
Inspect the shift linkage for proper alignment and operation.

Solution

1. Preparation

Gather tools and parts.
Disconnect the battery to ensure safety while working on electrical components.
Gather safety gear (gloves, goggles).

2. Check and Replace Transmission Fluid

Locate the transmission dipstick and remove it to check fluid level.
If fluid is low or discolored, drain the old fluid from the transmission pan.
- Tools: Socket set, drain pan.
Replace the transmission filter if equipped.
- Tools: Socket set, filter removal tool.
Refill the transmission with the manufacturer-recommended fluid type.
- Fluid type: Toyota ATF WS (check owner’s manual for specifics).
Start the engine and let it run for a few minutes; check the fluid level and top off if necessary.

3. Inspect and Replace Worn Transmission Mounts

Raise the vehicle securely on jack stands.
Inspect each transmission mount for cracks or excessive wear.
If damaged, remove the worn mount using a socket set.
Install the new transmission mount and torque it to the manufacturer’s specifications.
- Torque specification: Refer to repair manual for exact values.

4. Test and Replace Throttle Position Sensor (if necessary)

Disconnect the electrical connector from the throttle position sensor.
Use a multimeter to check the sensor’s resistance and voltage output.
If readings are outside the specified range, remove the old sensor using a socket set.
Install the new throttle position sensor and reconnect the electrical connector.