Toyota Corolla E170 (2013-2019) smells like burning oil what should I do

Toyota Corolla E170 (2013-2019)

Error Codes

1-3 hours

Time

medium

Difficulty

high

Severity

3 min read

493 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix burning oil smell in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before working near hot components.

Symptoms

•Burning oil smell inside or outside the vehicle
•Oil leak visible under the vehicle
•Engine overheating
•Decreased oil levels
•Smoke from the engine bay

Diagnostic Steps

1
Inspect for oil leaks: Visually check the engine and undercarriage for fresh oil spots or leaks.
2
Check oil level: Use the dipstick to verify the oil level; add oil if it's low.
3
Examine engine components: Look for worn or damaged gaskets, seals, or hoses that could be causing oil leakage.
4
Inspect exhaust system: Check for any signs of oil burning in the exhaust, which might indicate internal engine problems.
5
Scan for error codes: Use an OBD-II scanner to check for any engine-related trouble codes that might help identify the issue.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Oil filter wrench
•Socket set
•Torque wrench
•Drain pan
•Clean rags

Parts Required

•Replacement gasket or seal
•New oil filter
•Engine oil (as per specification)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect for oil leaks: Visually check the engine and undercarriage for fresh oil spots or leaks.
2
Check oil level: Use the dipstick to verify the oil level; add oil if it's low.
3
Examine engine components: Look for worn or damaged gaskets, seals, or hoses that could be causing oil leakage.
4
Inspect exhaust system: Check for any signs of oil burning in the exhaust, which might indicate internal engine problems.
5
Scan for error codes: Use an OBD-II scanner to check for any engine-related trouble codes that might help identify the issue.

Solution

1. Preparation

Gather Tools and Parts: Ensure you have all necessary tools and replacement parts before starting the repair.
Safety First: Disconnect the battery to prevent any electrical issues while working on the vehicle.

2. Resolve Oil Leak

Locate the Source: Identify the source of the oil leak by tracing the oil path back to the leaking component.
Replace Gaskets/Seals:
- Remove any components obstructing access to the leaking gasket or seal.
- Clean the mating surfaces with a solvent to ensure a proper seal.
- Apply a new gasket or sealant as per manufacturer specifications.
- Reinstall components and torque to specified values.

3. Change Oil if Necessary

Drain Old Oil: Place a drain pan underneath the oil pan, remove the drain plug, and allow old oil to fully drain.
Replace Oil Filter: Remove the old oil filter using an oil filter wrench. Lubricate the gasket on the new filter with fresh oil and install it.
Add New Oil: Replace the drain plug, and refill the engine with the manufacturer-recommended oil type and quantity.