my Toyota Corolla E170 (2013-2019) won’t start but the lights are working what to do

Toyota Corolla E170 (2013-2019)

Error Codes

1-3 hours

Time

medium

Difficulty

high

Severity

3 min read

492 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix a no-start condition in a 2013-2019 Toyota Corolla E170. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Electrical

Estimated Time

1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before inspecting the starter motor.

Symptoms

•Engine does not crank or start
•Dashboard lights illuminate but no engine response
•Clicking sound when trying to start the engine
•No sound or response from the starter motor
•Battery warning light may be illuminated

Diagnostic Steps

1
Check the battery voltage using a multimeter to ensure it's above 12.4 volts.
2
Inspect battery terminals for corrosion or loose connections.
3
Attempt to jump-start the vehicle to rule out a weak battery.
4
Test the ignition fuse and relay to ensure they are functioning.
5
Check for any error codes using an OBD-II scanner to identify potential issues.
6
Inspect the starter motor and connections for damage or wear.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Multimeter
•Wire brush
•Socket set
•Screwdriver set
•OBD-II scanner

Parts Required

•Battery (if faulty)
•Ignition fuse (if blown)
•Starter motor (if defective)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the battery voltage using a multimeter to ensure it's above 12.4 volts.
2
Inspect battery terminals for corrosion or loose connections.
3
Attempt to jump-start the vehicle to rule out a weak battery.
4
Test the ignition fuse and relay to ensure they are functioning.
5
Check for any error codes using an OBD-II scanner to identify potential issues.
6
Inspect the starter motor and connections for damage or wear.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is in a safe working environment.
Disconnect the negative battery cable to prevent electrical shorts.

2. Inspect and Clean Battery Connections

Remove the positive and negative battery cables.
Clean the terminals and cable ends with a wire brush to remove corrosion.
Reattach the cables securely, ensuring tight connections.

3. Test and Replace the Battery (if necessary)

Use a multimeter to measure the battery voltage.
If the voltage is below 12.4 volts, charge the battery or replace it if it fails to hold a charge.
If replacing, ensure the new battery matches the specifications of the original.

4. Check Ignition Fuse and Relay

Locate the fuse box and identify the ignition fuse.
Remove the fuse and inspect for continuity; replace if blown.
Test the ignition relay by swapping it with a similar relay in the fuse box to see if the issue resolves.

5. Inspect and Test Starter Motor

Locate the starter motor and check all connections for tightness and damage.
Use a multimeter to check for voltage at the starter motor while attempting to start the vehicle.
If no voltage is present, trace back to the ignition switch and wiring for faults.

Tools Required:

Multimeter
Wire brush
Socket set
Screwdriver set
OBD-II scanner

Parts Required:

Battery (if faulty)
Ignition fuse (if blown)
Starter motor (if defective)

Estimated Repair Time: 1-3 hours

Safety Warnings:

Disconnect the battery before working on electrical systems.
Allow the engine to cool before inspecting the starter motor.