my Toyota Corolla E170 (2013-2019) won't go into gear what should I check

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

534 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission issues in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool before opening any components.

Symptoms

•Gear shifter is unresponsive
•Grinding noise while attempting to shift
•Warning lights illuminated on the dashboard
•Fluid leaks under the vehicle
•Unusual vibrations during attempted gear shifts

Diagnostic Steps

1
Check the transmission fluid level and condition using the dipstick.
2
Inspect for any visible leaks around the transmission and under the vehicle.
3
Scan the vehicle's onboard computer using an OBD-II scanner for error codes related to the transmission.
4
Test the clutch pedal operation (for manual transmission) or brake pedal operation (for automatic transmission).
5
Inspect the gear shift linkage or cable for any disconnections or damage.
6
Check the condition of the transmission fluid for contamination or debris.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Wrench set
•Funnel
•Pliers
•Multimeter

Parts Required

•Transmission fluid
•Gear shift linkage (if damaged)
•Clutch master cylinder or brake light switch (if defective)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the transmission fluid level and condition using the dipstick.
2
Inspect for any visible leaks around the transmission and under the vehicle.
3
Scan the vehicle's onboard computer using an OBD-II scanner for error codes related to the transmission.
4
Test the clutch pedal operation (for manual transmission) or brake pedal operation (for automatic transmission).
5
Inspect the gear shift linkage or cable for any disconnections or damage.
6
Check the condition of the transmission fluid for contamination or debris.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the battery to prevent electrical shorts.

2. Check and Replace Transmission Fluid

Tools Required: Socket set, funnel, transmission fluid.
Locate the transmission fluid dipstick and remove it.
Inspect the fluid level; if low, add the recommended transmission fluid.
If the fluid is dark or has a burnt smell, drain the old fluid:
1. Place a drain pan under the transmission.
2. Remove the drain plug and allow fluid to drain completely.
3. Replace the drain plug and torque to the manufacturer’s specifications.
4. Refill with new transmission fluid through the dipstick tube.

3. Inspect and Repair Gear Shift Linkage

Tools Required: Wrench set, pliers.
Locate the gear shift linkage under the vehicle.
Inspect for any disconnections, broken parts, or misalignment.
If damaged, replace the linkage:
1. Remove any retaining clips or bolts securing the linkage.
2. Install the new linkage, ensuring proper alignment.
3. Secure with clips or bolts and verify the connection.

4. Check and Repair Clutch/Brake System (if applicable)

Tools Required: Wrench set, multimeter (if checking switch).
For manual transmission: Inspect the clutch master cylinder for leaks.
For automatic transmission: Verify the brake light switch is functioning.
If defective, replace the faulty component.