my Toyota Corolla E170 (2013-2019) transmission slips when I shift what to do

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

489 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission slipping issues in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostics, and repairs.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the transmission fluid pan to avoid burns.

Symptoms

•Slipping sensation during gear shifts
•Delayed engagement when selecting drive or reverse
•Unusual noises when the vehicle shifts gears
•Warning lights on the dashboard (e.g., check engine light)
•Decreased acceleration or poor performance
•Fluid leaks underneath the vehicle

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related codes.
2
Check the transmission fluid level and condition; look for discoloration or burnt smell.
3
Inspect the transmission fluid for leaks around the pan gasket and seals.
4
Test the transmission solenoids using a multimeter for proper resistance values.
5
Examine the transmission filter for clogging or contamination.
6
Conduct a road test to replicate the slipping issue and note specific conditions (e.g., speed, engine load).

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Multimeter
•Transmission fluid pump
•Drain pan

Parts Required

•Toyota ATF WS transmission fluid
•Transmission filter
•Transmission pan gasket
•Transmission solenoids (if defective)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related codes.
2
Check the transmission fluid level and condition; look for discoloration or burnt smell.
3
Inspect the transmission fluid for leaks around the pan gasket and seals.
4
Test the transmission solenoids using a multimeter for proper resistance values.
5
Examine the transmission filter for clogging or contamination.
6
Conduct a road test to replicate the slipping issue and note specific conditions (e.g., speed, engine load).

Solution

1. Preparation

Gather tools and parts needed for the repair.
Ensure the vehicle is on a level surface and securely supported with jack stands.
Disconnect the battery to prevent electrical shorts.

2. Check and Replace Transmission Fluid

Sub-steps:
1. Remove the transmission dipstick and wipe it clean.
2. Insert the dipstick back into the tube, remove it, and check the fluid level; fill if low.
3. If fluid is dark or burnt, drain the old transmission fluid by removing the drain plug or pan.
4. Replace with new fluid as specified in the owner’s manual (typically Toyota ATF WS).
5. Run the engine and cycle through the gears to circulate the new fluid.

3. Inspect and Replace Transmission Filter

Sub-steps:
1. Remove the transmission pan by unscrewing the bolts; be cautious of fluid spilling.
2. Take out the old filter and replace it with a new one.
3. Clean the pan and magnet, removing any metal debris.
4. Reinstall the pan with a new gasket, ensuring proper torque specifications (usually 7-10 ft-lbs).

4. Inspect and Test Transmission Components

Sub-steps:
1. Inspect the transmission solenoids for damage or signs of wear.
2. Replace defective solenoids, ensuring proper electrical connections.
3. Check wiring harness for frayed wires or poor connections, repairing as necessary.

5. Final Assembly and Testing

Sub-steps:
1. Reconnect the battery.
2. Start the engine and allow it to warm up to operational temperature.
3. Test drive the vehicle under various conditions to ensure proper shifting and performance.

Tools Required:

OBD-II scanner
Socket set
Torque wrench
Multimeter
Transmission fluid pump
Drain pan

Parts Required:

Toyota ATF WS transmission fluid
Transmission filter
Transmission pan gasket
Transmission solenoids (if defective)

Estimated Repair Time: 2-4 hours

Safety Warnings:

Disconnect the battery before working on electrical systems.
Allow the engine to cool before opening the transmission fluid pan to avoid burns.