my Toyota Corolla E170 (2013-2019) makes a grinding noise when turning what's wrong

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

562 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Diagnose and fix grinding noise when turning in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the vehicle is securely lifted and supported before working underneath.
•Disconnect the battery before working on electrical components.

Symptoms

•Grinding noise during left or right turns
•Vibration in the steering wheel while turning
•Difficulty in steering or a stiff feeling
•Uneven tire wear on the front tires
•Possible smell of burning rubber

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage to the CV joints and boots.
3
Examine the wheel bearings for play or roughness.
4
Test the steering components, including tie rods and ball joints, for wear.
5
Look for debris or foreign objects lodged in the wheel assembly.
6
Inspect the brake components for any signs of interference with the wheel.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Wheel chocks
•Socket set
•Torque wrench
•Pry bar
•Safety goggles

Parts Required

•Power steering fluid (if needed)
•CV joint (if damaged)
•Wheel bearing (if worn)
•Tie rod end or ball joint (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage to the CV joints and boots.
3
Examine the wheel bearings for play or roughness.
4
Test the steering components, including tie rods and ball joints, for wear.
5
Look for debris or foreign objects lodged in the wheel assembly.
6
Inspect the brake components for any signs of interference with the wheel.

Solution

1. Preparation

Tools Required: Jack, jack stands, wheel chocks, socket set, torque wrench, pry bar, and safety goggles.
Ensure the vehicle is parked on a level surface, and the engine is off.
Disconnect the battery to avoid any electrical issues during the inspection.

2. Inspect Power Steering System

Sub-steps:
1. Locate the power steering fluid reservoir.
2. Check the fluid level; add fluid if low and inspect for leaks.
3. If fluid is dark or contaminated, consider flushing the power steering system.

3. Check CV Joints and Boots

Sub-steps:
1. Raise the front of the vehicle and secure it with jack stands.
2. Inspect the CV joints for any tears or leaks in the boots.
3. Rotate the wheel and listen for noise; replace any damaged CV joints.

4. Inspect Wheel Bearings

Sub-steps:
1. Remove the front wheel using a socket set.
2. Check the wheel bearing for tightness by shaking the wheel; it should not have excessive play.
3. If play is detected, replace the wheel bearing.

5. Examine Steering Components

Sub-steps:
1. Inspect the tie rods and ball joints for wear or damage.
2. Use a pry bar to check for movement at the joints; replace any worn components.
3. Reassemble and torque all fasteners to the manufacturer specifications.

6. Brake Component Inspection

Sub-steps:
1. Inspect the brake pads and rotors for any abnormal wear or damage.
2. Check for any interference between brake components and the wheel assembly.
3. Replace any worn or damaged brake components.