my Toyota Corolla E170 (2013-2019) is making a grinding noise when turning, why?

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

549 words

Problem Statement

Learn how to diagnose and fix grinding noise when turning in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Ensure the vehicle is securely supported on jack stands before working underneath.
•Avoid spilling fluid, as it can damage paint.
•Always follow torque specifications when reassembling.
•Make sure to wear safety glasses and gloves when working under the vehicle.

Symptoms

•Grinding noise during turning
•Difficulty steering or increased resistance
•Vibration in the steering wheel
•Uneven tire wear
•Fluid leaks near the wheels or undercarriage

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage or wear on the CV joints and boots.
3
Examine the wheel bearings for signs of wear or failure.
4
Inspect the suspension components, including struts and control arms, for damage.
5
Lift the vehicle and rotate the wheels by hand to listen for grinding noises.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Funnel
•Axle puller
•Bearing puller

Parts Required

•Power steering fluid
•CV joint or axle assembly (if damaged)
•Wheel bearings (if worn)
•Suspension components (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage or wear on the CV joints and boots.
3
Examine the wheel bearings for signs of wear or failure.
4
Inspect the suspension components, including struts and control arms, for damage.
5
Lift the vehicle and rotate the wheels by hand to listen for grinding noises.

Solution

1. Preparation

Ensure the vehicle is parked on a flat surface.
Use wheel chocks to prevent rolling.
Disconnect the battery for safety.

2. Inspect and Replace Power Steering Fluid

Sub-steps:
1. Locate the power steering reservoir.
2. Check the fluid level and add the appropriate power steering fluid if low.
3. If the fluid is dirty, drain and replace it with fresh fluid.
Tools Required: Funnel, power steering fluid
Safety Warnings: Avoid spilling fluid, as it can damage paint.

3. Examine and Replace CV Joints

Sub-steps:
1. Remove the wheel and inspect the CV joint for tears in the boot.
2. If damaged, remove the axle from the transmission and replace the CV joint or the entire axle assembly.
Tools Required: Socket set, axle puller, torque wrench
Safety Warnings: Ensure the vehicle is securely supported on jack stands.

4. Check and Replace Wheel Bearings

Sub-steps:
1. Remove the brake rotor and caliper to access the wheel bearing.
2. Spin the bearing by hand to check for roughness or grinding.
3. If defective, remove the bearing and replace it with a new one.
Tools Required: Bearing puller, socket set, torque wrench
Safety Warnings: Always follow torque specifications when reassembling.

5. Inspect and Repair Suspension Components

Sub-steps:
1. Visually inspect struts and control arms for cracks or excessive wear.
2. Replace any damaged components as needed.
3. Have the alignment checked after any suspension repairs.
Tools Required: Socket set, torque wrench, alignment tools (if applicable)
Safety Warnings: Make sure to wear safety glasses and gloves when working under the vehicle.