my Toyota Corolla E170 (2013-2019) is jerking while driving, what's the cause?

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

560 words

Problem Statement

Learn how to diagnose and fix jerking issues in the 2013-2019 Toyota Corolla E170. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before working on any components.

Symptoms

•Jerking or stuttering during acceleration
•Engine misfires or rough running
•Decreased fuel efficiency
•Check engine light illuminated
•Unusual noises from the engine or drivetrain

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the engine air filter for clogs or obstructions that could affect airflow.
3
Check spark plugs for wear or fouling that may cause misfires.
4
Examine fuel injectors for blockages or malfunction.
5
Inspect the ignition system components, including ignition coils and wiring.
6
Test the throttle position sensor for proper function.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Multimeter
•Fuel injector cleaner

Parts Required

•Spark plugs (OEM recommended)
•Fuel injectors (if necessary)
•Throttle position sensor (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the engine air filter for clogs or obstructions that could affect airflow.
3
Check spark plugs for wear or fouling that may cause misfires.
4
Examine fuel injectors for blockages or malfunction.
5
Inspect the ignition system components, including ignition coils and wiring.
6
Test the throttle position sensor for proper function.

Solution

1. Preparation

Gather tools: OBD-II scanner, socket set, torque wrench, multimeter, and fuel injector cleaner.
Ensure the vehicle is on a level surface and securely parked.
Disconnect the battery to ensure safety.

2. Address Faulty Spark Plugs

Sub-step 1: Remove the engine cover if applicable.
Sub-step 2: Use a socket set to remove the spark plugs.
Sub-step 3: Inspect the spark plugs for wear or damage; replace them if necessary with OEM replacements.
Sub-step 4: Torque the new spark plugs to the manufacturer's specification (usually around 13-15 ft-lbs).

3. Clean or Replace Fuel Injectors

Sub-step 1: Disconnect the fuel pump fuse and start the engine until it stalls to relieve fuel pressure.
Sub-step 2: Disconnect the fuel injector connectors and remove the fuel rail (if necessary).
Sub-step 3: Clean the fuel injectors using a fuel injector cleaner kit or replace them if they are defective.
Sub-step 4: Reinstall the fuel rail and connectors securely.

4. Inspect and Test Ignition System

Sub-step 1: Check the ignition coils for cracks or signs of wear.
Sub-step 2: Use a multimeter to test the resistance of the ignition coils; replace any that are out of specification.
Sub-step 3: Reconnect all components and ensure all connections are secure.

5. Throttle Position Sensor Testing

Sub-step 1: Locate the throttle position sensor (TPS) and disconnect the electrical connector.
Sub-step 2: Use a multimeter to check the voltage output of the TPS at idle and full throttle; compare readings to manufacturer specifications.
Sub-step 3: Replace the TPS if it is out of specification.