my Toyota Corolla E170 (2013-2019) has low oil pressure warning light on

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

4 min read

613 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix low oil pressure warning in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Allow the engine to cool before working on the oil system.
•Ensure the vehicle is securely lifted if performing work underneath.

Symptoms

•Low oil pressure warning light illuminated on the dashboard
•Engine noise, such as ticking or knocking sounds
•Poor engine performance or sluggish acceleration
•Oil leakage under the vehicle
•Increased engine temperature

Diagnostic Steps

1
Check the engine oil level using the dipstick and add oil if necessary.
2
Scan the vehicle’s computer system with an OBD-II scanner to check for any trouble codes.
3
Inspect the oil pressure sending unit for any signs of damage or leaks.
4
Test the oil pressure using a mechanical oil pressure gauge.
5
Inspect oil filter for clogs or damage.
6
Examine the oil pump for proper operation.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Oil filter wrench
•Mechanical oil pressure gauge
•Oil catch pan

Parts Required

•Engine oil (0W-20 or as specified)
•Oil filter
•Oil pressure sending unit (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the engine oil level using the dipstick and add oil if necessary.
2
Scan the vehicle’s computer system with an OBD-II scanner to check for any trouble codes.
3
Inspect the oil pressure sending unit for any signs of damage or leaks.
4
Test the oil pressure using a mechanical oil pressure gauge.
5
Inspect oil filter for clogs or damage.
6
Examine the oil pump for proper operation.

Solution

1. Preparation

Gather tools and materials.
Ensure the vehicle is parked on a level surface and the engine is cool.
Disconnect the negative battery terminal to prevent electrical issues.

2. Check and Top Off Engine Oil

Remove the dipstick and wipe it clean.
Reinsert the dipstick and remove it again to check the oil level.
If the oil level is low, add the appropriate type of oil (typically 0W-20 for this model).
Recheck the oil level after adding oil.

3. Replace Oil Pressure Sending Unit (if faulty)

Locate the oil pressure sending unit, typically found near the oil filter.
Using a socket wrench, remove the old sending unit.
Install the new sending unit and ensure it is tightened according to the manufacturer’s specifications (usually hand-tight plus a quarter turn).
Reconnect the electrical connector.

4. Replace Oil Filter (if clogged)

Place an oil catch pan under the oil filter.
Use an oil filter wrench to remove the old oil filter.
Apply a small amount of new oil to the rubber gasket of the new filter.
Install the new oil filter by hand until it is snug, then tighten it according to specifications.

5. Change Engine Oil (if necessary)

Remove the oil drain plug using a socket set and allow old oil to drain completely into a catch pan.
Replace the oil drain plug and tighten it to the specified torque (typically 20-25 ft-lbs).
Fill the engine with new oil through the oil fill cap, using the recommended oil type and quantity (usually 4.5 quarts for a complete oil change).
Recheck oil level using the dipstick.

6. Reconnect Battery and Test

Reconnect the negative battery terminal.
Start the engine and let it idle.
Monitor the oil pressure warning light and listen for any unusual noises.