my Toyota Corolla E170 (2013-2019) has excessive oil consumption how to fix

Toyota Corolla E170 (2013-2019)

Error Codes

4-8 hours

Time

hard

Difficulty

high

Severity

3 min read

504 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix excessive oil consumption in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

4-8 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before working on it to prevent burns.

Symptoms

•Check engine light illuminated
•Blue smoke from the exhaust
•Engine knocking or ticking noises
•Low oil level warning
•Increased frequency of oil changes required
•Poor fuel economy

Diagnostic Steps

1
Check for DTC (Diagnostic Trouble Codes) using an OBD-II scanner to identify any related engine issues.
2
Inspect the oil level and condition, noting any signs of contamination or dilution.
3
Perform a visual inspection for oil leaks around gaskets, seals, and under the vehicle.
4
Conduct a compression test to assess the health of the engine cylinders.
5
Check the PCV (Positive Crankcase Ventilation) system for blockages or malfunctions.
6
Inspect the valve stem seals and piston rings for wear or damage, if accessible.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Valve spring compressor
•Oil catch pan
•Engine degreaser

Parts Required

•New valve cover gasket
•New oil pan gasket (if applicable)
•New PCV valve
•Valve stem seals (if replaced)
•Piston rings (if replaced)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check for DTC (Diagnostic Trouble Codes) using an OBD-II scanner to identify any related engine issues.
2
Inspect the oil level and condition, noting any signs of contamination or dilution.
3
Perform a visual inspection for oil leaks around gaskets, seals, and under the vehicle.
4
Conduct a compression test to assess the health of the engine cylinders.
5
Check the PCV (Positive Crankcase Ventilation) system for blockages or malfunctions.
6
Inspect the valve stem seals and piston rings for wear or damage, if accessible.

Solution

1. Preparation

Gather tools and parts.
Ensure the vehicle is on a level surface and secured with wheel chocks.
Disconnect the battery.

2. Address Oil Leaks

Sub-steps:
- Clean the engine surfaces with a degreaser to identify leaks.
- Replace any damaged gaskets (e.g., valve cover gasket, oil pan gasket) or seals.
- Re-torque bolts to manufacturer specifications if applicable.

3. Replace PCV Valve

Sub-steps:
- Locate the PCV valve on the engine.
- Disconnect the valve from the hose and remove it.
- Install the new PCV valve and reconnect the hose.

4. Inspect and Replace Valve Stem Seals (if necessary)

Sub-steps:
- Remove the valve cover.
- Use a valve spring compressor to remove the springs and access the valve stem seals.
- Replace worn seals with new ones, ensuring proper seating.
- Reassemble the valve cover and torque to specifications.

5. Replace Piston Rings (if necessary)

Sub-steps:
- Remove the engine from the vehicle if necessary.
- Remove the oil pan and cylinder head.
- Remove the pistons and replace the piston rings.
- Reassemble the engine, ensuring proper torque values are followed.