my Toyota Corolla E170 (2013-2019) has an oil consumption problem, what could it be

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

536 words

Problem Statement

Learn how to diagnose and fix oil consumption issues in the 2013-2019 Toyota Corolla E170. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool before opening drain plugs or removing components.

Symptoms

•Check engine light illuminated
•Unusual engine noise (ticking or knocking)
•Excessive exhaust smoke (blue smoke)
•Frequent need for oil top-ups
•Oil warning light activation
•Decreased engine performance (loss of power)

Diagnostic Steps

1
Check the engine oil level and condition using the dipstick.
2
Inspect for visible oil leaks around the engine and under the vehicle.
3
Perform a compression test on all cylinders to assess engine health.
4
Conduct a leak-down test to check for internal leaks in the engine.
5
Scan for diagnostic trouble codes (DTCs) using an OBD-II scanner.
6
Inspect the PCV (Positive Crankcase Ventilation) system for blockages or malfunctions.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Compression tester
•Leak-down tester
•Oil filter wrench
•Torque wrench
•Pliers
•Socket set

Parts Required

•PCV valve
•Valve cover gasket (if applicable)
•Oil pan gasket (if applicable)
•Engine oil and oil filter

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the engine oil level and condition using the dipstick.
2
Inspect for visible oil leaks around the engine and under the vehicle.
3
Perform a compression test on all cylinders to assess engine health.
4
Conduct a leak-down test to check for internal leaks in the engine.
5
Scan for diagnostic trouble codes (DTCs) using an OBD-II scanner.
6
Inspect the PCV (Positive Crankcase Ventilation) system for blockages or malfunctions.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Ensure the vehicle is parked on a level surface and the engine is cool.
Disconnect the battery to prevent electrical shorts.

2. Inspect and Replace PCV Valve

Locate the PCV valve: it is typically found on the valve cover.
Disconnect the PCV valve hose.
Remove the old PCV valve by twisting and pulling it out.
Install the new PCV valve by pushing it into place and reconnecting the hose.
Tools Required: Pliers, socket set

3. Address Engine Seals and Gaskets

Inspect the valve cover gasket and oil pan gasket for any signs of wear or leaks.
If leaks are identified, remove the affected components (valve cover or oil pan).
Clean the mating surfaces thoroughly.
Apply a new gasket or sealant as per manufacturer specifications and reassemble components.
Tools Required: Gasket scraper, torque wrench

4. Engine Oil Change

Drain the old engine oil by removing the oil drain plug.
Replace the oil filter using an oil filter wrench.
Reinstall the oil drain plug and torque it to manufacturer specifications.
Fill the engine with the recommended oil type and amount as per the owner's manual.
Tools Required: Oil filter wrench, wrench set, oil catch pan