my Toyota Corolla E170 (2013-2019) has a delay when I press the gas pedal is that normal

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

529 words

Problem Statement

Learn how to diagnose and fix throttle delay issues in the 2013-2019 Toyota Corolla E170. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening any components.

Symptoms

•Delay in acceleration when pressing the gas pedal
•Engine hesitation during acceleration
•Unresponsive throttle at times
•Poor fuel economy
•Check engine light may be illuminated

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the throttle position sensor (TPS) for proper operation and any signs of wear.
3
Check the air intake system for blockages or leaks, including the air filter and intake hoses.
4
Evaluate the fuel delivery system, including checking the fuel pump pressure.
5
Examine the engine vacuum system for leaks that could affect performance.
6
Test the accelerator pedal position sensor for proper function.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Screwdriver
•Multimeter
•Throttle body cleaner

Parts Required

•Throttle position sensor (if faulty)
•Accelerator pedal position sensor (if faulty)
•Air filter (if clogged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the throttle position sensor (TPS) for proper operation and any signs of wear.
3
Check the air intake system for blockages or leaks, including the air filter and intake hoses.
4
Evaluate the fuel delivery system, including checking the fuel pump pressure.
5
Examine the engine vacuum system for leaks that could affect performance.
6
Test the accelerator pedal position sensor for proper function.

Solution

1. Preparation

Gather the necessary tools and parts.
Ensure the vehicle is parked on a flat surface and the engine is off before starting any repairs.

2. Inspect and Replace Throttle Position Sensor (if needed)

Tools Required: Socket set, screwdriver, multimeter
Locate the throttle position sensor on the throttle body.
Disconnect the electrical connector from the TPS.
Remove the screws or bolts securing the TPS and carefully take it off.
Use a multimeter to test the resistance of the TPS according to the specifications in the service manual.
If out of range, install a new throttle position sensor:
- Position the new TPS and secure it with screws/bolts.
- Reconnect the electrical connector.

3. Clean the Throttle Body

Tools Required: Throttle body cleaner, rags, socket set
Remove the intake duct connected to the throttle body.
Using throttle body cleaner and a rag, clean the throttle body to remove carbon buildup.
Ensure the throttle plate moves freely without obstruction.
Reattach the intake duct securely.

4. Test and Replace Accelerator Pedal Position Sensor (if faulty)

Tools Required: Multimeter
Disconnect the electrical connector from the accelerator pedal position sensor.
Use a multimeter to check the voltage readings according to specifications.
If readings are outside the specified range, replace the accelerator pedal position sensor:
- Remove the screws securing the sensor.
- Install the new sensor and reconnect the electrical connector.